lt3082ets8 Linear Technology Corporation, lt3082ets8 Datasheet - Page 3

• Manufacturer Part Number: lt3082ets8
• Description: 200ma Single Resistor Low Dropout Linear Regulator
• Manufacturer: Linear Technology Corporation

ELECTRICAL CHARACTERISTICS
temperature range, otherwise specifi cations are at T
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: Unless otherwise specifi ed, all voltages are with respect to V
The LT3082E is tested and specifi ed under pulse load conditions such
that T
–40°C and 125°C is assured by design, characterization, and correlation
with statistical process controls. The LT3082I is guaranteed to meet all
data sheet specifi cations over the full –40°C to 125°C operating junction
temperature range. The LT3082MP is 100% tested and guaranteed over
the –55°C to 125°C operating junction temperature range.
Note 3: Minimum load current is equivalent to the quiescent current of
the part. Since all quiescent and drive current is delivered to the output
of the part, the minimum load current is the minimum current required to
maintain regulation.
PARAMETER
SET Pin Current
Offset Voltage (V
Load Regulation (Note 7)
Line Regulation
Minimum Load Current (Note 3)
Dropout Voltage (Note 4)
Current Limit
Error Amplifi er RMS Output Noise (Note 5)
Reference Current RMS Output Noise (Note 5)
Ripple Rejection
Thermal Regulation
J
≅ T
A
. The LT3082E is 100% tested at T
OUT
– V
SET
)
I
V
ΔI
ΔV
ΔI
ΔV
I
SET
SET
OS
A
SET
SET
OS
OS
= 25°C. Performance at
CONDITIONS
V
2V ≤ V
V
V
ΔI
ΔI
ΔV
ΔV
2V ≤ V
I
I
V
I
C
10Hz ≤ f ≤ 100kHz
f = 120Hz, V
C
f = 10kHz
f = 1MHz
10ms Pulse
LOAD
LOAD
LOAD
IN
IN
IN
IN
SET
OUT
LOAD
LOAD
IN
IN
= 2V, I
= 2V, I
= 2V, I
= 5V, V
= 2V to 40V, I
= 2V to 40V, I
= 0.1μF
J
= 2.2μF , C
= 10mA
= 200mA
= 200mA, 10Hz ≤ f ≤ 100kHz, C
IN
IN
= 25°C. (Note 2)
= 1mA to 200mA
= 1mA to 200mA
≤ 40V, 1mA ≤ I
≤ 40V
LOAD
LOAD
LOAD
SET
RIPPLE
The
OUT
= 0V, V
SET
= 1mA
= 1mA
= 1mA
.
l
LOAD
LOAD
= 0.1μF
= 0.5V
denotes the specifi cations which apply over the full operating
OUT
LOAD
= 1mA
= 1mA
P-P
Note 4: For the LT3082, dropout is specifi ed as the minimum input-to-
output voltage differential required supplying a given output current.
Note 5: Adding a small capacitor across the reference current resistor
lowers output noise. Adding this capacitor bypasses the resistor shot
noise and reference current noise; output noise is then equal to error
amplifi er noise (see the Applications Information section).
Note 6: Diodes with series 1k resistors clamp the SET pin to the OUT pin.
These diodes and resistors only carry current under transient overloads.
Note 7: Load regulation is Kelvin-sensed at the package.
Note 8: This IC includes overtemperature protection that protects the
device during momentary overload conditions. Junction temperature
exceeds the maximum operating junction temperature when
overtemperature protection is active. Continuous operation above the
specifi ed maximum operating junction temperature may impair device
reliability.
= –0.1V
, I
≤ 200mA
LOAD
= 0.1A,
OUT
= 10μF ,
l
l
l
l
l
l
l
9.90
9.80
MIN
200
–2
–4
0.003
0.003
–0.1
–0.5
0.03
1.22
TYP
300
300
1.3
0.7
10
10
33
90
75
20
LT3082
10.10
10.20
0.010
MAX
1.45
1.65
500
0.2
–2
2
4
UNITS
μV
nA
mV/V
%/W
3
nA/V
3082f
RMS
RMS
mV
mV
mV
mA
μA
μA
nA
μA
dB
dB
dB
V
V