bcm352f110t300a00 Vicor Corporation, bcm352f110t300a00 Datasheet
bcm352f110t300a00
Related parts for bcm352f110t300a00
bcm352f110t300a00 Summary of contents
Page 1
... Case temperature Operating junction temperature Storage temperature Note: (1) The referenced junction is defined as the semiconductor having the highest temperature. This temperature is monitored by a shutdown comparator. 800-735-6200 V•I Chip Bus Converter BCM352F110T300A00 & BCM352T110T300A00 BCM352F110T300A00 BCM352T110T300A00 (Formerly VIB0001TFJ) © Vin = 330 - 365 V Vout = 10.3 - 11.4 V Iout = 28 ...
Page 2
... Figure 2 — Output voltage turn-on waveform with PC enabled at full load and 352 Vin Figure 4 — Input reflected ripple current at full load and 352 Vin 800-735-6200 V•I Chip Bus Converter BCM352F110T300A00 & BCM352T110T300A00 Note PC low Using test circuit in Figure 18; See Figure 1 Using test circuit in Figure 18; See Figure 4 200 nH maximum source inductance ...
Page 3
... Figure 6 — Power dissipation as a function of output power 800-735-6200 V•I Chip Bus Converter BCM352F110T300A00 & BCM352T110T300A00 Note No load Full load W 354 - 365 V IN ≤300 W P OUT Max pulse width 1ms, max duty cycle 10%, ...
Page 4
... Figure 8 — Output voltage ripple at full load and 352 Vin with 10 µF ceramic external bypass capacitor and distribution inductance. Figure 10 — 0 -28.0 A load step with 2 µF input capacitor and no output capacitor. 800-735-6200 V•I Chip Bus Converter BCM352F110T300A00 & BCM352T110T300A00 Rev. 1.6 Page ...
Page 5
... Unit 4.8 5.0 5.2 2.4 2.5 2.5 2.6 2.4 2.5 2 Figure 13 — PC signal during over current fault 800-735-6200 V•I Chip Bus Converter BCM352F110T300A00 & BCM352T110T300A00 Unit Note Mhrs 25°C, GB Vdc Input to Output pF Input to Output MΩ Input to Output UL /CSA 60950-1, EN 60950-1 Low Voltage Directive See Mechanical Drawings, Figures 15 & ...
Page 6
... Owing to the wide bandwidth and low output impedance of the BCM, low frequency bypass capacitance and significant energy storage may be more densely and efficiently provided by adding capacitance at the input of the BCM. vicorpower.com Figure 14 — BCM pin configuration 800-735-6200 V•I Chip Bus Converter BCM352F110T300A00 & BCM352T110T300A00 ...
Page 7
... DIMENSIONS ARE inch . 2. UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE [.XX] = +/-0.25 / [.01]; .XX / [.XXX] = +/-0.13 / [.005] 3. PRODUCT MARKING ON TOP SURFACE DXF and PDF files are available on vicorpower.com Figure 16 — BCM PCB land layout information vicorpower.com 800-735-6200 V•I Chip Bus Converter BCM352F110T300A00 & BCM352T110T300A00 Rev. 1.6 Page ...
Page 8
... Figure 17 — Hole location for push pin heat sink relative to V vicorpower.com TOP SIDE SHOWN I Chip • 800-735-6200 V•I Chip Bus Converter BCM352F110T300A00 & BCM352T110T300A00 NOTES: 1. MAINTAIN 3.50 [0.138] DIA. KEEP-OUT ZONE FREE OF COPPER, ALL PCB LAYERS. 2. (A) MINIMUM RECOMMENDED PITCH IS 39.50 [1.555], THIS PROVIDES 7.00 [0.275] COMPONENT EDGE-TO-EDGE SPACING, AND 0 ...
Page 9
... I Q – – 800-735-6200 V•I Chip Bus Converter BCM352F110T300A00 & BCM352T110T300A00 Notes: + Source inductance should be no more than 200 nH. If source inductance is greater than 200 nH, additional bypass capacitance may be required. Load C3 should be placed close to the load µF R3 may be ESR separate damping resistor. ...
Page 10
... Application Notes For BCM and V•I Chip application notes on soldering, thermal management, board layout, and system design click on the link below: http://www.vicorpower.com/technical_library/application_information/chips/ 800-735-6200 V•I Chip Bus Converter BCM352F110T300A00 & BCM352T110T300A00 Rev. 1.6 Page ...
Page 11
... D496,906; D505,114; D506,438; D509,472 and for use under 6,975,098 and 6,984,965 Customer Service: custserv@vicorpower.com Technical Support: apps@vicorpower.com vicorpower.com 800-735-6200 Vicor Corporation 25 Frontage Road Andover, MA, USA 01810 Tel: 800-735-6200 Fax: 978-475-6715 email V•I Chip Bus Converter BCM352F110T300A00 & BCM352T110T300A00 Rev. 1.6 12/10 ...