icx415aq Sony Electronics, icx415aq Datasheet
icx415aq
Related parts for icx415aq
icx415aq Summary of contents
Page 1
... Diagonal 8mm (Type 1/2) Progressive Scan CCD Image Sensor with Square Pixel for Color Cameras Description The ICX415AQ is a diagonal 8mm (Type 1/2) interline CCD solid-state image sensor with a square pixel array. Progressive scan allows all pixel's signals to be output independently within approximately 1/50 second. ...
Page 2
... The terms and conditions in the Sony additional specifications, which will be made available to you when you order the Products, shall also be applicable to your use of the Products as well as to this specifications book. You should review those terms and conditions when you consider purchasing and/or using the Products. – 2 – ICX415AQ ...
Page 3
... Note) Note) : Photo sensor 22 Description V Supply voltage DD RG Reset gate clock V Protective transistor bias L SUB Substrate clock H Horizontal register transfer clock 1 H Horizontal register transfer clock Substrate bias SUB Supply voltage for the substrate SUBCIR voltage generation NC ICX415AQ ...
Page 4
... Ratings Unit Remarks –0.3 to +55 V –0.3 to +18 V –55 to +10 V – +17 V –16 to +16 V –10 to +15 V –55 to +10 V –65 to +0.3 V –0.3 to +27.5 V –0.3 to +22.5 V –0.3 to +17.5 V –30 to +80 °C –10 to +60 °C –10 to +75 °C ICX415AQ 1 ...
Page 5
... Do not apply a DC bias to the reset gate clock pins, because a DC bias is generated within the CCD. DC Characteristics Item Supply current Symbol Min. Typ. V 14.55 15 SUB Integer portion Decimal portion Symbol Min. Typ. I 4.0 7.0 DD – 5 – Max. Unit Remarks 15. Max. Unit Remarks 9.0 mA ICX415AQ power L ...
Page 6
... VL2 VL3 , V 6.8 7.5 8. – 0.1 VL3 0.5 0.5 0.5 0.5 4.75 5.0 5.25 –0.05 0 0.05 0.8 2.5 4.5 5.0 5.5 – V 0.8 RGLL – V 0.5 RGLm 21.5 22.5 23.5 – 6 – ICX415AQ Waveform Remarks Diagram VH02 VL1 V 2 (During 29.5MHz VL1 V 2 (During 14.75MHz High-level coupling V 2 High-level coupling ...
Page 7
... GND V23 Horizontal transfer clock equivalent circuit RG – 7 – Typ. Min. Max. Unit Remarks 3900 pF 3300 pF 3300 pF 2200 pF 2200 pF 1800 390 100 , ICX415AQ ...
Page 8
... VHH V VHL V VLH V VL2 V VLL V VH3 V VHH V VHL V VLH VH02 + V )/2 VL01 VL03 – 8 – VL03 M 0V and – VH1 VL01 – VH02 VL2 – VH3 VL03 ICX415AQ ...
Page 9
... Point A is the minimum value of the coupling waveform during the period from RGLL and V . RGLH RGLL RGLm 100% 90% V SUB 10 twh – 9 – twl V HL and H waveforms and H is two twl . ICX415AQ . CR V RGL ...
Page 10
... Unit During 0.5 0.5 µs readout When using 15 350 ns CXD3400N 10 17 When draining 0.5 0.4 µs charge 1 and H is two ICX415AQ Remarks During readout When using CXD3400N tf tr – 2ns When draining charge Remarks tr – 2ns ...
Page 11
... Zone 0 Ignored region Effective pixel region Gr/Gb AMP S/H R/B S/H – 11 – Remarks 1 1/25s accumulation conversion value 60° Zone 60° 60°C 8 Gr/Gb channel signal output [ B] R/B channel signal output [ C] ICX415AQ (Ta = 25°C) ...
Page 12
... R signal and Gr signal lines and Gb signal and B signal lines are output sequentially. The primary color filters of this image sensor are arranged in the layout shown in the figure on the left (Bayer arrangement). Gr and Gb denote the G signals on the same line as the R signal and the B signal, respectively. Horizontal register – 12 – ICX415AQ ...
Page 13
... There are the mode (100 frames/s) which outputs 264 lines of an output line portion, and the mode (200 frames/s) which outputs 88 lines (2) Center scan mode Undesired portions (Swept by vertical register high-speed transfer) – 13 – Picture center cut-out portion ICX415AQ ...
Page 14
... Gra + Gba + log Vsm 2 , color temperature of 3200K halogen source subject and the center of each Gr, Gb, R and B channel [dB] (1/10V method conversion value) 4 500 10 – 14 – ICX415AQ ...
Page 15
... Adjust the Gr signal output value generated by the strobe light to 120mV. After setting the strobe light so that it strobes with the following timing, measure the residual signal amount (Vlag). Substitute the value into the following formula. Lag = (Vlag/120) 100 [%] VD V2 Strobe light timing Output 100 [%] 100 [%] 100 [%] Light Gr signal output 120mV Vlag(lag) – 15 – ICX415AQ ...
Page 16
Drive Circuit 15V 0.1 1/35V 3. XSUB XV3 4 17 XSG3 5 16 CXD3400N XV2 XSG2 XV1 100k 0.1 ...
Page 17
... Spectral Sensitivity Characteristics (Excludes lens characteristics and light source characteristics) 1.0 0.8 0.6 0.4 0.2 0 400 450 G B 500 550 600 Wave Length [nm] – 17 – R 650 700 ICX415AQ ...
Page 18
Drive Timing Chart (Vertical Sync) Progressive Scan Mode VD "a" OUT ...
Page 19
Drive Timing Chart (Vertical Sync "a" Enlarged) "a" Enlarged Progressive Scan Mode/Center Scand Mode 627 701 ...
Page 20
Drive Timing Chart (Horizontal Sync) Progressive Scan Mode CLK H1 H2 SHP SHD SUB ...
Page 21
Drive Timing Chart (Vertical Sync) Center Scan Mode 1 VD "d" "a" OUT "b" "c" "d" "a" "b" ...
Page 22
Drive Timing Chart (Horizontal Sync) Center Scan Mode 1 (Frame Shift) ("b" 16048 bits = 17H #166 ...
Page 23
Drive Timing Chart (Horizontal Sync) Center Scan Mode 1 (High-speed Sweep) ("d" 18880 bits = 20H #194 ...
Page 24
Drive Timing Chart (Vertical Sync) Center Scan Mode 2 VD "d" "a" OUT "b" "c" "d" "a" "b" ...
Page 25
Drive Timing Chart (Horizontal Sync) Center Scan Mode 2 (Frame Shift) ("b" 24544 bits = 26H #254 ...
Page 26
Drive Timing Chart (Horizontal Sync) Center Scan Mode 2 (High-speed Sweep) ("d" 29264 bits = 31H #299 ...
Page 27
... If a load is applied to the entire surface by a hard component, bending stress may be generated and the package may fracture, etc., depending on the flatness of the ceramic portions. Therefore, for installation, use either an elastic load, such as a spring plate adhesive. 29N Shearing strength Tensile strength – 27 – ICX415AQ 29N 0.9Nm Torsional stregth ...
Page 28
... For continuous using under cruel condition exceeding the normal using condition, consult our company. b) Exposure to high temperature or humidity will affect the characteristics. Accordingly avoid storage or usage in such conditions. c) Brown stains may be seen on the bottom or side of the package. But this does not affect the CCD characteristics. – 28 – ICX415AQ ...
Page 29
Package Outline Unit: mm 0.7 9 18.0 ± 0.4 14.6 0.69 (For the 1st.pin only) 1.27 0.3 Cer-DIP PACKAGE MATERIAL LEAD TREATMENT TIN PLATING LEAD MATERIAL 42 ALLOY PACKAGE MASS 2.60g DRAWING NUMBER AS-B15-03(E) 22 ...