cxa2119m Sony Electronics, cxa2119m Datasheet
cxa2119m
Available stocks
Related parts for cxa2119m
cxa2119m Summary of contents
Page 1
... Y color difference I/F Description The CXA2119M is a video switch IC developed for Y color difference I/F used in televisions. Features • Two YCbCr input systems, one RGB input system, one YCbCr output system • Three inputs, one output for composite video signal • On-chip matrix circuit for RGB signal signal • ...
Page 2
... Low: Y2, Cb2, Cr2 inputs selected VILMAX = 1V VIHMIN = 40k Clamp pulse input pin. High: CLP ON 129 Low: CLP OFF VILMAX = 2.5V 3.4V VIHMIN = RGB signal input pins. 129 Input 100 IRE, 0.7Vp-p signals via capacitors. 40k 3.5V 120k 55µ – 2 – CXA2119M Description ...
Page 3
... GND pin 100µ YSSW control pin. High: RGB input system selected 2.5V Low: YCbCr input system selected VILMAX = 1V VIHMIN = 100µ YMSW control pin. High: –6dB signal selected Low: 0dB signal selected VILMAX = 1V VIHMIN = 3V – 3 – CXA2119M Description ...
Page 4
... Inputs 1Vp-p (100% white including sync) signals via capacitors. 22k Control pins for 3 input composite video signal output selection switch. 52µ SEL1 129 Low High Low 100k High VILMAX = 0.5V 70k VIHMIN = 3.5V – 4 – CXA2119M Description SEL2 SIG OUT Low SIG1 Low SIG2 High SIG3 High Prohibited ...
Page 5
... CXA2119M ...
Page 6
... Note: Set as follows unless otherwise specified in the measurement conditions column of Electrical Characteristics 5V 3.8V 0V, SW1, SW2, SW3: ON, are all GND. 9V 10µ 0.01µ 10µ 0.1µ 0.1µ 0.1µ 10µ 10µ – 6 – CXA2119M 10µ 0.1µ 0.1µ 0.1µ SW1 SW2 SW3 V2 ...
Page 7
... SIG output YS signal 10µ input YM signal input 0.01µ 10µ 0.1µ 0.1µ 0.1µ 10µ 10µ clamp pulse YCbCr2 inputs RGB inputs input – 7 – CXA2119M YCbCr outputs 10µ 0.1µ 0.1µ 0.1µ ...
Page 8
... Description of Operation The CXA2119M has two input systems for the YCbCr signal (Y1, Cb1, Cr1 IN: Pins Y2, Cb2, Cr2 IN: Pins 5 to 7). These two signals (specified input level: 100% color bar, 0.7Vp-p) are input via capacitors, and are clamped to approximately 4V at the timing of the CLP pulse input to CLP (Pin 8). After clamping, they pass the 6dB amplifier, and one system is selected by INPUT SEL (Pin 4) control. The selected YCbCr signal is controlled by YM (Pin 21) for 0/– ...
Page 9
... Unit 0.45 ± 0.1 SONY CODE SOP-28P-L04 EIAJ CODE SOP028-P-0375-D JEDEC CODE 28PIN SOP (PLASTIC) 375mil + 0.4 18.8 – 0 1.27 M ± 0.12 PACKAGE STRUCTURE PACKAGE MATERIAL LEAD TREATMENT LEAD MATERIAL PACKAGE WEIGHT – 9 – CXA2119M + 0.4 2.3 – 0.15 0.15 + 0.2 0.1 – 0.05 + 0.1 0.2 – 0.05 EPOXY / PHENOL RESIN SOLDER PLATING 42 ALLOY 0.7g ...