ps7122al-1c-e4 California Eastern Laboratories, ps7122al-1c-e4 Datasheet

Page 1

... DIP, 250 V BREAK DOWN VOLTAGE, TRANSFER TYPE 2-ch Optical Coupled MOS FET DESCRIPTION The PS7122A-1C and PS7122AL-1C are transfer type solid state relays containing normally open (N.O.) contact and normally close (N.C.) contact on the output side. They are suitable for analog signal control because of their low offset and high linearity. ...

Page 2

... M 2 PS7122A-1C,PS7122AL-1C PS7122A-1C TOP VIEW 7.62 6.5±0 15˚ PS7122AL-1C TOP VIEW 6.5±0.5 0.9±0.25 9.60±0.4 Data Sheet PN10275EJ01V1DS 1. LED Anode 2. LED Cathode 3. LED Anode 4. LED Cathode 5. MOS FET (N.O.) 6. MOS FET (N.O.) 7 ...

Page 3

... ORDERING INFORMATION (Pb-Free) Part Number Package PS7122A-1C-A 8-pin DIP Magazine case 50 pcs PS7122AL-1C-A PS7122AL-1C-E3-A Embossed Tape 1 000 pcs/reel PS7122AL-1C-E4-A *1 For the application of the Safety Standard, following part number should be used. ABSOLUTE MAXIMUM RATINGS (T Parameter Symbol Diode Forward Current (DC) Reverse Voltage V Power Dissipation ...

Page 4

... RECOMMENDED OPERATING CONDITIONS (T Parameter Symbol LED Operating Current LED Off Voltage V 4 PS7122A-1C,PS7122AL- °C) A MIN. TYP. MAX. Unit 0 Data Sheet PN10275EJ01V1DS ...

Page 5

... C Coupled LED On-state Current I LED Off-state Current I On-state Resistance Turn-on Time t on (N.O (N.C.) *1 Turn-off Time t off (N.O.) t off (N.C.) Isolation Resistance R Isolation Capacitance C PS7122A-1C,PS7122AL- °C) A Conditions N.O mA 250 V Loff F D N.C mA 250 N.O MHz ...

Page 6

... Test Circuit for Switching Time Pulse Input Input monitor N.O. (between pin 5 and 6) Input Output PS7122A-1C,PS7122AL- monitor N.C. (between pin 7 and Input Output 10 % off Data Sheet PN10275EJ01V1DS off ...

Page 7

... ˚C A N.O., N.C. – ˚C –8 10 N.O., N.C. – 100 150 Applied Voltage V (V) D PS7122A-1C,PS7122AL- °C, unless otherwise specified) A MAXIMUM LOAD CURRENT vs. AMBIENT TEMPERATURE 300 200 100 100 –25 (˚C) OUTPUT CAPACITANCE vs. APPLIED VOLTAGE 400 300 ...

Page 8

... NORMALIZED ON-STATE RESISTANCE vs. AMBIENT TEMPERATURE 3.0 Normalized to 1 ˚ (N.O.), mA (N.C 2.0 1.5 1.0 0.5 0.0 – Ambient Temperature T (˚ PS7122A-1C,PS7122AL-1C TURN-OFF TIME vs. FORWARD CURRENT NORMALIZED TURN-OFF TIME vs. AMBIENT TEMPERATURE 3.0 2 2.0 N.O. 1.5 N.C. 1.0 0.5 0.0 75 100 – ...

Page 9

... Turn-on Time t (ms) on TURN-ON TIME (N.C.) DISTRIBUTION pcs 0.04 0.05 Turn-on Time t (ms) on Remark The graphs indicate nominal characteristics. PS7122A-1C,PS7122AL-1C ON-STATE RESISTANCE (N.C.) DISTRIBUTION mA 4.7 4.3 On-state Resistance R TURN-OFF TIME (N.O.) DISTRIBUTION mA ...

Page 10

... TAPING SPECIFICATIONS (in millimeters) Outline and Dimensions (Tape) 2.0±0.1 4.0±0.1 1.55±0.1 Tape Direction PS7122AL-1C-E3 Outline and Dimensions (Reel) R 1.0 Packing: 1 000 pcs/reel 10 PS7122A-1C,PS7122AL-1C +0.1 1.5 –0 10.4±0.1 12.0±0.1 PS7122AL-1C-E4 2.0±0.5 13.0±0.2 21.0±0.8 Data Sheet PN10275EJ01V1DS 4.5 MAX. 4.0 ±0.1 0.3 2.0±0.5 17.5±1.0 21.5±1.0 15.9 to 19.4 Outer edge of flange ...

Page 11

... Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (3) Cautions • Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. PS7122A-1C,PS7122AL-1C 260°C or below (package surface temperature) 10 seconds or less 60 seconds or less 120±30 s ...

Page 12

Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) ...