MIC2787-YHYMT MICREL [Micrel Semiconductor], MIC2787-YHYMT Datasheet
MIC2787-YHYMT
Related parts for MIC2787-YHYMT
MIC2787-YHYMT Summary of contents
Page 1
... The MIC2786 features integrated pull-up resistors on the /MR0 and /MR1 inputs, while the MIC2787 requires external pull-up resistors. The PDY input pin selects between a 2s setup period. Factory-programmed reset timeout delays of 140ms (min ...
Page 2
... MIC2787-YFYMT 7YF (2) MIC2787-XGYMT 7XG (2) MIC2787-YGYMT 7YG (2) MIC2787-XHYMT 7XH (2) MIC2787-YHYMT 7YH Notes: 1. All devices available in Tape and Reel only. 2. Contact Factory for availability. ® 3. Thin MLF ▲ = Pin 1 identifier. ® 4. Thin MLF is a Green RoHS-compliant package. Lead finish is NiPdAu. Mold compound is Halogen Free. ...
Page 3
... GND Supply Ground. Active-Low Manual Reset Input. The MIC2786 has an internal 65kΩ pull-up resistor to VIN, while the MIC2787 requires an external pull-up resistor to VIN if used with a push button. Pull this pin low to 3 /MR1 assert and force a reset. Pulling both manual reset inputs low for the setup delay time causes one reset output pulse for the reset timeout delay period ...
Page 4
... MIC2786/MIC2787 Max. Units V 5.5 12.5 µA 4.718 4.741 4.463 4.484 3.137 3.152 2.984 2.998 V 2.678 2.691 2.359 2.371 2.232 2 ...
Page 5
... 1.0mA IN SINK = 4.5V 0.8mA IN SOURCE = 2.7V 0.5mA IN SOURCE = 1.6V 250μA IN SOURCE V = 5.5V /RST MIC2786 only ) /MR0, /MR1 inputs; MIC2787 only MR PDY = V , /MR0 = /MR1 = 0V IN PDY = V , /MR0 = V or /MR1 PDY = 0V, /MR0 = /MR1 = 0V PDY = 0V, /MR0 = V or /MR1 = MIC2786/MIC2787 Min. Typ. 0.5 1.0 2.0 1.6 4.0 3.2 6.0 4 ...
Page 6
... V = 3.0V IN PDY = 0V 240 230 220 210 200 -40 -15 TEMPERATURE (°C) Reset Timeout Delay (Option vs. Temperature (PDY = V IN 250 V = 3.0V IN PDY = V IN 240 230 220 210 200 -40 -15 TEMPERATURE (°C) MIC2786/MIC2787 M9999-102711-A ...
Page 7
... TEMPERATURE (°C) October 2011 Setup Delay vs. Input Voltage 10.0 8.0 6.0 4.0 2.0 0 INPUT VOLTAGE ( Reset Timeout Delay (Option X ) vs. Input Voltage 250 240 PDY = V IN 230 PDY = 0V 220 PDY = OPEN 210 200 INPUT VOLTAGE (V) MIC2786/MIC2787 M9999-102711-A ...
Page 8
... Micrel, Inc. Timing Diagram October 2011 8 MIC2786/MIC2787 M9999-102711-A ...
Page 9
... Micrel, Inc. Functional Diagram October 2011 9 MIC2786/MIC2787 M9999-102711-A ...
Page 10
... Figure possible to tie this resistor to some other voltage, other than V /RST output. The pull-up voltage must be limited to 5.5V or less to avoid damage to the MIC2786/MIC2787. The pull-up resistor must be small enough to supply current to the inputs and leakage paths that are driven by the /RST output (a recommended value is 100kΩ ...
Page 11
... V as 1.6V. The RSTP output is a compliment of the /RST output. October 2011 V The MIC2786/MIC2787 is relatively immune to small negative-going V shown in Figure 4, the overdrive voltage is the difference between the threshold voltage and the minimum point of the V duration of 20μs or less will not cause a reset. ...
Page 12
... Micrel, Inc. Typical Applications Figure 5. MIC2786/MIC2787 Used for Interrupting System Power Figure 6. MIC2786/MIC2787 Used for Microcontroller Reset October 2011 12 MIC2786/MIC2787 M9999-102711-A ...
Page 13
... GRM188R71C104KA01D R1, R2, R4 CRCW0603100KJNEA MIC2786-XDYMT U1 MIC2787-XDYMT Notes: 1. Murata Tel: www.murata.com. 2. Vishay Tel: www.vishay.com. 3. Micrel, Inc.: www.micrel.com. October 2011 Manufacturer Description (1) Murata 0.1µF, 16V capacitor, X7R, 0603 (2) Vishay 100k, 5% resistor, 0603 (3) Micrel, Inc. Push-Button Reset IC with Supply Voltage Supervisor 13 MIC2786/MIC2787 Qty M9999-102711-A ...
Page 14
... Micrel, Inc. PCB Layout Recommendations October 2011 Top Layer Top Silkscreen 14 MIC2786/MIC2787 M9999-102711-A ...
Page 15
... Micrel, Inc. PCB Layout Recommendations (Continued) October 2011 Copper Layer Bottom Silkscreen 15 MIC2786/MIC2787 M9999-102711-A ...
Page 16
... Micrel, Inc. Package Information October 2011 8-Pin 2mm × 2mm Thin MLF ® 16 MIC2786/MIC2787 M9999-102711-A ...
Page 17
... Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully October 2011 8-Pin 2mm × 2mm Thin MLF indemnify Micrel for any damages resulting from such use or sale. © 2011 Micrel, Incorporated. 17 MIC2786/MIC2787 ® http://www.micrel.com M9999-102711-A ...