MIC2788 MICREL [Micrel Semiconductor], MIC2788 Datasheet
MIC2788
Related parts for MIC2788
MIC2788 Summary of contents
Page 1
... Both manual reset inputs can be tied together if a single push-button reset is desired. The MIC2788 features integrated pull-up resistors on the /MR0 and /MR1 inputs, while the MIC2789 requires external pull-up resistors. The PDY input pin selects between a 2s set-up period ...
Page 2
... GND Supply Ground. Active-Low Manual Reset Input. The MIC2788 has an internal 65kΩ pull-up resistor to VIN while the MIC2789 requires an external pull-up resistor to VIN if used with a push-button. Pull this pin 3 /MR1 low to assert and force a reset. Pulling both manual reset inputs low for the setup delay time causes one reset output pulse for the reset timeout delay period ...
Page 3
... Pin Function No Connect. Leave pin floating. Active-Low Manual Reset Input. The MIC2788 has an internal 65kΩ pull-up resistor to VIN while the MIC2789 requires an external pull-up resistor to VIN if used with a push-button. Pull this pin low to assert and force a reset. Pulling both manual reset inputs low for the setup delay time causes one reset output pulse for the reset timeout delay period. If unused, connect to VIN ...
Page 4
... 250μA IN SOURCE V = 5.5V /RST 4 (2) )..................................... +1.6V to +5. .......................... –40°C to +85°C A ® 2mm × 2mm Thin MLF (θ ).............................90°C/W JA Min. Typ. 1.6 3.4 2.9 2.0 1.6 4.0 3.2 6.0 4.8 220 140 350 240 0.8 × VIN 0.8 × VIN 0.8 × VIN MIC2788/MIC2789 Max. Units V 5.5 7.5 µA 2.4 s 4.8 7.2 280 ms 480 0.3 V 0.3 0.3 V μA 0.3 M9999-102711-A ...
Page 5
... MR Programmable Setup Delay Input (PDY) Input Bias Current PDY Pin (I ) PDY October 2011 (4) (Continued) ≤ +85°C; unless noted otherwise. A Conditions MIC2788 only /MR0, /MR1 inputs; MIC2789 only PDY = V , /MR0 = /MR1 = 0V IN PDY = V , /MR0 = V or /MR1 PDY = 0V, /MR0 = /MR1 = 0V ...
Page 6
... V = 3.0V IN PDY = 0V 240 230 220 210 200 60 85 -40 -15 TEMPERATURE (°C) Reset Timeout Delay (Option X) ) vs. Temperature (PDY = V IN 250 V = 3.0V IN PDY = V IN 240 230 220 210 200 -40 -15 TEMPERATURE (°C) MIC2788/MIC2789 M9999-102711-A ...
Page 7
... INPUT VOLTAGE (V) October 2011 Setup Delay vs. Input Voltage 10.0 8.0 PDY =V 6.0 PDY = 0V 4.0 PDY =OPEN 2.0 0 INPUT VOLTAGE (V) 7 MIC2788/MIC2789 Reset Timeout Delay (Option X) vs. Input Voltage 250 240 IN 230 220 210 200 INPUT VOLTAGE (V) M9999-102711 ...
Page 8
... Micrel, Inc. Timing Diagram October 2011 8 MIC2788/MIC2789 M9999-102711-A ...
Page 9
... Micrel, Inc. Functional Diagram October 2011 9 MIC2788/MIC2789 M9999-102711-A ...
Page 10
... MOSFET structure that requires a pull-up resistor. For most applications, the pull-up voltage will be the same as the power supply that supplies V MIC2788/MIC2789. As shown in Figure possible October 2011 to tie this resistor to some other voltage, other than V thus enabling level-shifting of the /RST output. The pull- up voltage must be limited to 5 ...
Page 11
... Micrel, Inc. Typical Applications October 2011 Figure 3. MIC2788/89 Used for Interrupting System Power Figure 4. MIC2788/89 Used for Microcontroller Reset 11 MIC2788/MIC2789 M9999-102711-A ...
Page 12
... Part Number C1 GRM188R71C104KA01D R1, R2, R4 CRCW0603100KJNEA U1 MIC2788-XYMT MIC2789-XYMT Notes: 1. Murata Tel: www.murata.com. 2. Vishay Tel: www.vishay.com. 3. Micrel, Inc.: www.micrel.com. October 2011 Manufacturer Description (1) Murata 0.1µF, 16V capacitor, X7R, 0603 (2) Vishay 100k, 5% resistor, 0603 (3) Micrel, Inc. Push-Button Supervisor Reset ICs 12 MIC2788/MIC2789 Qty M9999-102711-A ...
Page 13
... Micrel, Inc. PCB Layout Recommendations October 2011 Top Layer Top Silkscreen 13 MIC2788/MIC2789 M9999-102711-A ...
Page 14
... Micrel, Inc. PCB Layout Recommendations (Continued) October 2011 Copper Layer Bottom Silkscreen 14 MIC2788/MIC2789 M9999-102711-A ...
Page 15
... Micrel, Inc. Package Information October 2011 8-Pin 2mm × 2mm Thin MLF ® 15 MIC2788/MIC2789 M9999-102711-A ...
Page 16
... Micrel, Inc. Recommended Landing Pattern October 2011 8-Pin 2mm × 2mm Thin MLF ® 16 MIC2788/MIC2789 M9999-102711-A ...
Page 17
... Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully October 2011 indemnify Micrel for any damages resulting from such use or sale. © 2011 Micrel, Incorporated. 17 MIC2788/MIC2789 http://www.micrel.com M9999-102711-A ...