MIC68400-1.8YML MICREL [Micrel Semiconductor], MIC68400-1.8YML Datasheet
MIC68400-1.8YML
Available stocks
Related parts for MIC68400-1.8YML
MIC68400-1.8YML Summary of contents
Page 1
... The MIC68400 operates from a wide input range of 1.65V to 5.5V, which includes all of the main supply voltages commonly available today designed to drive digital circuits requiring low voltage at high currents (i.e. PLDs, DSP, microcontroller, etc ...
Page 2
... Micrel, Inc. Typical Application Sequenced Dual Power Supply for I/O and Core Voltage of µProcessor August 2009 2 MIC68400 M9999-081809-C ...
Page 3
... Micrel, Inc. Tracking Dual Power Supply for I/O and Core Voltage of µProcessor August 2009 3 MIC68400 M9999-081809-C ...
Page 4
... Output Error Low Voltage EN Sequencing Timer/Controller DLY Ordering Information Part Number Current MIC68400-1.8YML MIC68400YML NOTE: For additional voltage options, contact Micrel Marketing. ® MLF is a GREEN RoHS compliant package. Lead finish is NiPdAu. Mold compound is Halogen Free. August 2009 Ramp External on ...
Page 5
... Output Voltage Sense Pin: Connect directly to output pin. Adjustable regulators: Feedback input. Connect to resistor voltage divider. Output Voltage: Output of voltage regulator. Place capacitor to ground to bypass the output voltage. Minimum load current is 100µA. Nominal bypass capacitor is 10µF. 5 ® 16-Pin 4mm × 4mm MLF (ML) Adjustable Voltages M9999-081809-C MIC68400 ...
Page 6
... V ≥ 1V (Regulator enable 5.5V; POR = High POR Output Logic-Low Voltage (undervoltage condition 1mA POR Threshold below nominal OUT Hysteresis V = 0.75V DELAY V = High POR 6 MIC68400 (2) ) ....................................... 1.65V to 5.5V IN )..................................... )............................................. ..............................................30°C/W JA ≤ +125°C, unless noted. J Min Typ Max -2 +2 0.50 0.49 0.51 20 ...
Page 7
... Measure (VOUT – TARGET ; 500mV)) RC TARGET (ambient temperature Min Typ Max 1 0.7 1 -50 25 100 RC - – θ . Exceeding the maximum D(max) J(max and Adj/Sns pin, or the rated output OUT M9999-081809-C MIC68400 Units µ ...
Page 8
... Micrel, Inc. Typical Characteristics August 2009 8 MIC68400 M9999-081809-C ...
Page 9
... Micrel, Inc. Functional Characteristics August 2009 9 MIC68400 M9999-081809-C ...
Page 10
... For simple applications the enable (EN) can be connected to V MIC68400 only requires a few µA’s of enable current to turn on, actual enable pin current will depend on the overdrive (enable voltage exceeding 1V) in each particular application. ...
Page 11
... Fixed Parts driven from another (Master) regulator the two outputs will track each other until the Master exceeds the target voltage of the Slave regulator. Typically the output of the MIC68400 will track above the RC input by 30mV to 70mV. This offset is designed to allow Master/Slave tracking of same-voltage regulators ...
Page 12
... RC pin for low values of output capacitor the maximum discharge current available at the output for large values of output capacitor. Turn off slew rate is not a specified characteristic of the MIC68400. Sequencing Configurations Sequencing refers to timing based Master/Slave control between regulators. It allows a Master device to control the start and stop timing of a single or multiple Slave devices ...
Page 13
... POR delay during turn-on. Fixed Voltage Devices August 2009 Fixed voltage versions of MIC68400 have two internal voltage dividers: one for setting the output voltage and the other for driving the tracking circuitry. Adjustable parts have up to two external dividers: one from ...
Page 14
... Also, when RC is driven in tracking mode, pulling EN low will not cause the output to drop. Maintaining low EN in tracking mode simply means that the MIC68400 will shutdown when the tracking voltage gets near zero case can the MIC68400 enter the tracking mode unless EN is pulled high. August 2009 ...
Page 15
... Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully August 2009 16-Pin 4mm x 4mm MLF (ML) indemnify Micrel for any damages resulting from such use or sale. © 2007 Micrel, Incorporated. 15 MIC68400 for surgical implant M9999-081809-C ...