LT1016_03 LINER [Linear Technology], LT1016_03 Datasheet
LT1016_03
Related parts for LT1016_03
LT1016_03 Summary of contents
Page 1
FEATURES TM ■ UltraFast (10ns typ) Operates Off Single 5V Supply or ±5V ■ ■ Complementary Output to TTL ■ Low Offset Voltage ■ No Minimum Input Slew Rate Requirement ■ No Power Supply Current Spiking Output Latch Capability ■ ...
Page 2
LT1016 ABSOLUTE AXI U RATI GS Positive Supply Voltage (Note 5) ............................... 7V Negative Supply Voltage ............................................ 7V Differential Input Voltage (Note 7) ........................... ±5V +IN, –IN and LATCH ENABLE Current (Note 7) .. ±10mA Output Current ...
Page 3
ELECTRICAL CHARACTERISTICS temperature range, otherwise specifications are at T SYMBOL PARAMETER V Input Offset Voltage OS DV Input Offset Voltage Drift Input Offset Current OS I Input Bias Current B Input Voltage Range CMRR Common Mode Rejection ...
Page 4
LT1016 W U TYPICAL PERFOR A CE CHARACTERISTICS Gain Characteristics 5.0 = ± 4 OUT T = 125°C J 4.0 3.5 3 25°C J 2.5 2.0 1 – 55°C 1.0 ...
Page 5
W U TYPICAL PERFOR A CE CHARACTERISTICS Negative Supply Current vs Temperature 6 = ± OUT 100 125 –50 – JUNCTION TEMPERATURE (°C) 1016 ...
Page 6
LT1016 U U APPLICATIO S I FOR ATIO Common Mode Considerations The LT1016 is specified for a common mode range of –3.75V to 3.5V with supply voltages of ±5V. A more general consideration is that the common mode range is ...
Page 7
U U APPLICATIO S I FOR ATIO The circuit shown in Figure 1 is the best electronic means of generating a known fast, clean step to test comparators. It uses a very fast transistor in a common base configura- tion. ...
Page 8
LT1016 U U APPLICATIO S I FOR ATIO Other common problems include different measurement results using various pieces of test equipment, inability to make measurement connections to the circuit without inducing spurious responses and dissimilar operation between two “identical” circuits. ...
Page 9
U U APPLICATIO S I FOR ATIO In Figure 4 the LT1016’s supplies are bypassed, but it still oscillates. In this case, the bypass units are either too far from the device or are lossy capacitors. Use capacitors with good ...
Page 10
LT1016 U U APPLICATIO S I FOR ATIO In Figure 7 the probes are properly selected and applied but the LT1016’s output rings and distorts badly. In this case, the probe ground lead is too long. For general purpose work ...
Page 11
U U APPLICATIO S I FOR ATIO “Fuzz” on the edges is the difficulty in Figure 10. This condition appears similar to Figure 10, but the oscillation is more stubborn and persists well after the output has gone low. This ...
Page 12
LT1016 U U APPLICATIO S I FOR ATIO Another output-caused fault is shown in Figure 13. The output transitions are initially correct but end in a ringing condition. The key to the solution here is the ringing. What is happening ...
Page 13
U U APPLICATIO S I FOR ATIO 1.8ms, 12-Bit A/D Converter The LT1016’s high speed is used to implement a very fast 12-bit A/D converter in Figure 15. The circuit is a modified form of the standard successive approximation approach ...
Page 14
LT1016 U TYPICAL APPLICATIO S Voltage Controlled Pulse Width Generator 5V FULL-SCALE LM385 CALIBRATION 1.23V 500Ω 2N3906 1k 25Ω 2N3906 100pF 1000pF 5V 2. LT1016 – 2. –5V 1k 1N914 2N3906 470pF ...
Page 15
U TYPICAL APPLICATIO S 1MHz to 10MHz Crystal Oscillator 5V 1MHz TO 10MHz 2k CRYSTAL LT1016 2k OUTPUT – Q GND LATCH – 0.068µF 1016 AI04 U APPE DIX A About Level Shifts ...
Page 16
LT1016 U APPE DIX A +V OUTPUT = 0V TO TYPICALLY LT1016 OUTPUT Figure A1 + INPUT LT1016 – INVERTING VOLTAGE GAIN—BIPOLAR SWING t = 3ns RISE t = 3ns FALL TRACE A 2V/DIV TRACE B 10V/DIV ...
Page 17
PLIFIED SCHE ATIC LT1016 17 ...
Page 18
LT1016 PACKAGE DESCRIPTIO 0.300 – 0.325 (7.620 – 8.255) 0.009 – 0.015 (0.229 – 0.381) +0.035 0.325 –0.015 ( +0.889 8.255 –0.381 *THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH ...
Page 19
PACKAGE DESCRIPTIO 0.010 – 0.020 (0.254 – 0.508) 0.008 – 0.010 (0.203 – 0.254) (0.406 – 1.270) * DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE ** DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. ...
Page 20
LT1016 APPLICATIO S I FOR ATIO 1Hz to 10MHz V-to-F Converter The LT1016 and the LT1122 FET input amplifier combine to form a high speed V-to-F converter in Figure 16. A variety of techniques is used to ...