LT1567_1 LINER [Linear Technology], LT1567_1 Datasheet
LT1567_1
Related parts for LT1567_1
LT1567_1 Summary of contents
Page 1
FEATURES ■ Single-Ended to Differential Conversion ■ Low Noise: 1.4nV/√Hz ■ 20µV Total Wideband Noise in Filter RMS with 2MHz f C Dynamic Range: 104dB SNR at ±5V ■ ■ Total Supply Voltage: 2.7V to 12V ■ Rail-to-Rail Outputs ■ ...
Page 2
LT1567 ABSOLUTE AXI U RATI GS (Note 1) + – Total Supply Voltage ( ............................ 12.6V Input Current (Note 2) ........................................ ±25mA Operating Temperature Range (Note 3) LT1567C ..............................................–40°C to 85°C LT1567I ...............................................–40°C to ...
Page 3
ELECTRICAL CHARACTERISTICS The ● denotes the specifications that apply over the full operating temperature range (Note 4), otherwise specifications and typical = ±2.5V, R values are 25° PARAMETER OA Input Bias Current DC ...
Page 4
LT1567 W U TYPICAL PERFOR A CE CHARACTERISTICS OA Open-Loop Gain and Phase vs Frequency –10 –20 –30 0 FREQUENCY (MHz) Closed-Loop Gain and Phase of OA and INV vs ...
Page 5
W U TYPICAL PERFOR A CE CHARACTERISTICS Output Impedance vs Frequency 100 = ± 25° –10 V INVERTER –1 V 0.01 0.001 100k 1M 10M 100M ...
Page 6
LT1567 CTIO S OAOUT (Pin 1): Output of the Uncommitted Op Amp (OA). As with most wideband op amps important to avoid connecting heavy capacitive loads (above about 10pF) directly to this output. ...
Page 7
W BLOCK DIAGRA OAOUT OAIN BYPASS – + INV 2 – 3 7pF 150Ω – 4 LT1567 + INVOUT 600Ω 600Ω 6 INVIN DC BIAS 5 1567 BD 1567fa 7 ...
Page 8
LT1567 U U APPLICATIO S I FOR ATIO Functional Description The LT1567 contains two low noise rail-to-rail output, wideband operational amplifiers, one of them connected internally as a unity-gain inverter. These two amplifiers can form a second order multiple feedback ...
Page 9
U U APPLICATIO S I FOR ATIO The simple-to-use spreadsheet requires the user to de- fine the desired corner (or center) frequency, the pass- band gain and a capacitor value for a choice of second or third order Chebyshev or ...
Page 10
LT1567 U U APPLICATIO S I FOR ATIO output from the INV block (Pin 7). These two outputs maintain equal gain and 180º phase shift over a wide frequency range. This feature permits choosing the signal polarity in single ended ...
Page 11
U U APPLICATIO S I FOR ATIO 0.1µ REF Figure 3. A Single Ended to Differential Amplifier LT1567 600Ω 600Ω 2 – – 7pF 150Ω + – ...
Page 12
LT1567 U U APPLICATIO S I FOR ATIO Figure 4 shows an LT1567 single supply differential buffer driving a differential 1st order RC filter. The V is subject to the common mode (DC BIAS) limits in the spec table. Within ...
Page 13
U U APPLICATIO S I FOR ATIO V IN2 R1 V IN1 V REF WITH R3 AND R1 EQUAL, V GAIN FROM ( 604Ω, THEN NOISE ...
Page 14
LT1567 U U APPE DIX: OUTPUT OISE VERTI G A PLIFIER NOISE THEN the voltage noise density in V/√Hz at the inverter’s ON output. V ...
Page 15
PACKAGE DESCRIPTIO 5.23 (.206) MIN 0.42 ± 0.038 (.0165 ± .0015) TYP RECOMMENDED SOLDER PAD LAYOUT 0.254 (.010) GAUGE PLANE 0.18 (.007) NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS ...
Page 16
LT1567 U TYPICAL APPLICATIO 649Ω 40.2Ω 604Ω 90.9Ω 2200pF 220pF RELATED PARTS PART NUMBER DESCRIPTION ® LTC 1560-1 1MHz/500kHz Continuous Time, Lowpass Elliptic Filter LTC1562/LTC1562-2 Universal 8th Order Active RC Filters LTC1563-2/LTC1563-3 4th Order Active RC Lowpass Filters ...