LTC3836 LINER [Linear Technology], LTC3836 Datasheet - Page 6

• Manufacturer Part Number: LTC3836
• Description: Dual 2-Phase, No RSENSETM Low VIN Synchronous Controller
• Manufacturer: LINER [Linear Technology]

LTC3836
PIN FUNCTIONS
SW1/SW2 (Pins 1, 14)/(Pins 26, 11): Switch Node
Connection to Inductor and External MOSFETs. Also the
negative input to differential peak current comparator
and an input to the reverse current comparator. Normally
connected to the source of the main MOSFET, the drain of
the synchronous MOSFET, and the inductor.
NC (Pins 2, 18)/(Pins 16, 28): No Connection.
IPRG1/IPRG2 (Pins 3, 6)/(Pins 27, 3): Three-State Pins
to Select Maximum Peak Sense Voltage Threshold. These
pins select the maximum allowed voltage drop between
the SENSE
across the external main MOSFET) for each channel. Tie
to V
respectively.
V
Receives the remotely sensed feedback voltage for its con-
troller from an external resistor divider across the output.
I
and Error Amplifi er Compensation Point. Nominal operat-
ing range on these pins is from 0.7V to 2V. The voltage on
these pins determines the threshold of the main current
comparator.
PLLLPF (Pin 7)/(Pin 4): Frequency Set/PLL Lowpass
Filter. When synchronizing to an external clock, this pin
serves as the lowpass fi lter point for the phase-locked
loop. Normally a series RC is connected between this pin
and ground.
When not synchronizing to an external clock, this pin serves
as the frequency select input. Tying this pin to GND selects
300kHz operation; tying this pin to V
operation. Floating this pin selects 550kHz operation.
SGND (Pin 8)/(Pin 5): Small-Signal Ground. This pin serves
as the ground connection for most internal circuits.
V
pin powers the entire chip except for the gate drivers.
Externally fi ltering this pin with a lowpass RC network
(e.g., R = 10Ω, C = 1μF) is suggested to minimize noise
pickup, especially in high load current applications.
TRACK/SS2 (Pin 10)/(Pin 7): Channel 2 Tracking and Soft-
Start Input. The LTC3836 regulates the V
6
TH1
FB1
IN
/I
IN
(Pin 9)/(Pin 6): Small-Signal Power Supply. This
/V
TH2
, GND or fl oat to select 202mV, 82mV, or 122mV
FB2
(Pins 5, 12)/(Pins 2, 9): Current Threshold
+
(Pins 4, 11)/(Pins 1, 8): Feedback Pins.
and SW pins (i.e., the maximum allowed drop
(GN Package)/(UFD Package)
IN
FB2
selects 750kHz
voltage to the
smaller of 0.6V or the voltage on the TRACK/SS2 pin. An
internal 1.5μA pull-up current source is connected to this
pin. A capacitor to ground at this pin sets the ramp time
to fi nal regulated output voltage. Alternatively, a resistor
divider on another voltage supply connected to this pin
allows the LTC3836 output to track the other supply dur-
ing start-up.
PGOOD (Pin 13)/(Pin 10): Power-Good Output Voltage
Monitor Open-Drain Logic Output. This pin is pulled to
ground when the voltage on either feedback pin (V
V
PGND (Pins 17, 22, 26)/(Pins 14, 19, 23): Power Ground.
These pins serve as the ground connection for the gate
drivers and the negative input to the reverse current
comparators. The Exposed Pad must be soldered to PCB
ground.
RUN/SS (Pin 20)/(Pin 17): Run Control Input and Op-
tional External Soft-Start Input. Forcing this pin below
0.65V shuts down the chip (both channels). Driving this
pin to V
the chip’s internal soft-start. An external soft-start can
be programmed by connecting a capacitor between this
pin and ground.
TG1/TG2 (Pins 23, 21)/(Pins 20, 18): Top Gate Drive
Output. These pins drive the gates of the external topside
MOSFETs. These pins have an output swing from PGND
to BOOST.
SYNC/FCB (Pin 24)/(Pin 21): This pin performs two
functions: 1) external clock synchronization input for
phase-locked loop, and 2) pulse-skipping operation or
forced continuous mode select. To synchronize with an
external clock using the PLL, apply a CMOS compatible
clock with a frequency between 250kHz and 850kHz. To
select pulse-skipping operation at light loads, tie this
pin to V
operation, which allows the inductor current to reverse.
When synchronized to an external clock, pulse-skipping
operation is enabled at light loads.
BG1/BG2 (Pins 25, 19)/(Pins 22, 15): Bottom Gate
Drive Output. These pins drive the gates of the external
synchronous MOSFETs. These pins have an output swing
from PGND to BOOST.
FB2
) is not within ±13.3% of its nominal set point.
IN
IN
. Grounding this pin selects forced continuous
or releasing this pin enables the chip, using
3836fa
FB1
,