LTC4050 LINER [Linear Technology], LTC4050 Datasheet

no-image

LTC4050

Manufacturer Part Number
LTC4050
Description
Lithium-Ion Linear Battery Charger with Thermistor Interface
Manufacturer
LINER [Linear Technology]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LTC4050EMS-4.1
Manufacturer:
LT
Quantity:
10 000
Part Number:
LTC4050EMS-4.1
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LTC4050EMS-4.2
Manufacturer:
LT
Quantity:
10 000
Part Number:
LTC4050EMSE-4.2
Manufacturer:
LINEAR/凌特
Quantity:
20 000
FEATURES
APPLICATIO S
TYPICAL APPLICATIO
*SHUTDOWN INVOKED BY FLOATING THE PROG PIN
0.1 F
Complete Standalone Linear Charger Controller
for 1-Cell Lithium-Ion Batteries
Thermistor Interface for Battery Temperature
Sensing
Preset Charge Voltage with 1% Accuracy
Programmable Charge Current
C/10 Charge Current Detection Output
Programmable Charge Termination Timer
Input Supply (Wall Adapter) Detection Output
4.5V to 10V Input Voltage Range
Automatic Sleep Mode When Input Supply
is Removed (Only 5 A Battery Drain)
Automatic Trickle Charging of Low Voltage Cells
Automatic Battery Recharge
Battery Insertion Detection
Space Saving 10-Pin MSOP Package
Cellular Phones
Handheld Computers
Charging Docks and Cradles
1k
1k
Single Cell 4.2V 500mA Li-Ion Battery Charger
10
3
4
CHRG
ACPR
TIMER
LTC4050-4.2
GND
5
V
CC
8
U
SENSE
NTC
PROG
DRV
BAT
2
9
7
1
6
*
19.6k
U
V
6V
IN
Si9430DY
0.2
I
MBRM120T3
10 F
BAT
= 500mA
+
4.2V
Li-Ion
CELL
1 F
4050 TA01
Charger with Thermistor Interface
T
10k NTC
DALE NTHS-1206N02
DESCRIPTIO
The LTC
constant-current/constant-voltage linear charge control-
lers for lithium-ion (Li-Ion) batteries. Charge current is
programmable and final float voltage has 1% accuracy.
When the input supply is removed, the LTC4050 automati-
cally enters a low quiescent current sleep mode, dropping
the battery drain current to 5 A. An internal comparator
detects the near-end-of-charge (C/10) condition while a
programmable timer, using an external capacitor, sets the
total charge time. Fully discharged cells are automatically
trickle charged at 10% of the programmed current until
cell voltage exceeds 2.49V. The thermistor interface
suspends charging if the cell temperature is outside of a
0 C to 50 C temperature window.
The LTC4050 begins a new charge cycle when a discharged
battery is connected to the charger or when the input power
is applied. In addition, a new charge cycle is automatically
started if the battery remains connected to the charger and
the cell voltage drops below 3.88V for 4.1V cells or below
3.98V for 4.2V cells.
The LTC4050 is available in the 10-pin MSOP package.
, LTC and LT are registered trademarks of Linear Technology Corporation.
Lithium-Ion Linear Battery
®
4050-4.1/LTC4050-4.2 are complete standalone
600
500
400
300
200
100
U
0
–50
V
BAT
–25
THERMISTOR TEMPERATURE ( C)
Thermistor Temperature
= 3.7V
Charge Current vs
0
25
50
LTC4050
75
100
4050 TA05
125
1
4050f

Related parts for LTC4050

LTC4050 Summary of contents

Page 1

... The thermistor interface suspends charging if the cell temperature is outside temperature window. The LTC4050 begins a new charge cycle when a discharged battery is connected to the charger or when the input power is applied. In addition, a new charge cycle is automatically started if the battery remains connected to the charger and the cell voltage drops below 3 ...

Page 2

... unless otherwise noted CONDITIONS Charger On, Current Mode Shutdown Mode Sleep Mode (Battery Drain Current) LTC4050-4. 10V LTC4050-4. 10V LTC4050-4. 10V CC LTC4050-4. 10V 19.6k 0.2 PROG SENSE R = 19.6k 0.2 PROG SENSE R = 97.6k 0.2 PROG ...

Page 3

... High to Low (LTC4050-4.1) BAT V from High to Low (LTC4050-4.2) BAT Note 2: The LTC4050E is guaranteed to meet performance specifications from Specifications over the – operating temperature range are assured by design, characterization and correlation with statistical process controls. Charge Current vs V ...

Page 4

... V (V) CC LTC4050 G08 NTC R Threshold Voltage HOT vs Temperature 4. 4.14 4.12 4.10 4.08 4.06 4.04 – –25 0 TEMPERATURE ( C) LTC4050 G11 NTC R Threshold Voltage COLD 28. 28.55 28.50 28.45 28. (V) CC LT4050 G14 LTC4050 G09 75 100 125 LTC4050 G12 8 10 LTC4050 G15 ...

Page 5

... This resistor is chosen using the following equation • 800 )/(R SENSE PROG ACPR (Pin 10): Wall Adapter Present Output. When the input voltage (wall adaptor) is applied to the LTC4050, this = TIMER pin is pulled to ground by an internal N-channel MOSFET that is capable of sinking 5mA suitable for driving an external LED. LTC4050 BAT • ...

Page 6

... PROG – C/10 720 LOGIC SLP OSCILLATOR COUNTER 3.6V V REF + A1 – 2.3 A PROG 6 • SENSE R PROG + 3.88V (LTC4050-4.1) 3.98V (LTC4050-4.2) C5 – SENSE + 54mV – 800 + C4 – – DRV CA + – BAT C2 LBO + – REF 2.47V CHARGE GND 5 4050 BD R SENSE 9 ...

Page 7

... U OPERATIO The LTC4050 is a linear battery charger controller. The charge current is programmed by the combination of a program resistor (R ) from the PROG pin to ground PROG and a sense resistor (R ) between the V SENSE pins. R sets a program current through an internal PROG trimmed 800 resistor setting up a voltage drop from V to the input of the current amplifier (CA) ...

Page 8

... CHRG pin output becomes high impedance. Shutdown The LTC4050 can be forced into shutdown by floating the PROG pin and allowing the internal 2.3 A current source to pull the pin above the 3.6V shutdown threshold voltage. In shutdown, the DRV pin is pulled the external P-channel MOSFET and resetting the internal timer ...

Page 9

... By using two different value pull-up resistors, a microprocessor can detect three states from this pin (charging, C/10 and stop charging). See Figure 1. When the LTC4050 is in charge mode, the CHRG pin is pulled low by an internal N-channel MOSFET. To detect this mode, force the digital output pin, OUT, high and measure the voltage at the CHRG pin ...

Page 10

... LTC4050 U U APPLICATIONS INFORMATION If a PNP transistor is chosen as the pass transistor, a 1000pF capacitor is required from the DRV pin to V capacitor is needed to help stabilize the voltage loop capacitor at the BAT pin is also recommended when a battery is not present. V Bypass Capacitor CC Many types of capacitors can be used for input bypassing. ...

Page 11

... BSC 4.90 0.15 DETAIL “A” (1.93 .006) 0.254 (.010) 0 – 6 TYP 0.53 0.01 (.021 .006) DETAIL “A” SEATING PLANE 0.17 – 0.27 (.007 – .011) TYP LTC4050 0.497 0.076 (.0196 .003 REF 3.00 0.102 (.118 .004) NOTE 0.86 1.10 (.034) (.043) REF MAX 0 ...

Page 12

... Li-Ion 2 5 CELL 0. 0.082 8 1/ SENSE 3 CHRG ACPR 1 1 DRV Si2305DS 7 LTC1693-5 LTC4050-4 TIMER BAT 6 PROG 15 H 0.1 F CDRH6D28-150NC NTC GND 19. 4.1V Li-Ion 10k NTC CELL DALE NTHS-1206N02 COMMENTS V Can Be Higher or Lower Than Battery Voltage, 1.5A Switch IN Precise Output Current Programming 32V V Time or Charge Current Termination, Automatic Charger/Battery Detection, Status Output, Preconditioning, 8-Lead MSOP ...

Related keywords