LZ2364BJ Sharp Electrionic Components, LZ2364BJ Datasheet - Page 5

• Manufacturer Part Number: LZ2364BJ
• Description: 1/3-type CCD Area Sensors with 470 k Pixels
• Manufacturer: Sharp Electrionic Components

CHARACTERISTICS FOR LZ2364BJ
(T
Color temperature of light source : 3 200 K, IR cut-off filter (CM-500, 1 mmt) is used.)
NOTES :
Standard output voltage
Photo response non-uniformity
Saturation output voltage
Dark output voltage
Dark signal non-uniformity
Sensitivity
Gamma
Smear ratio
Image lag
Blooming suppression ratio
Output transistor drain current
Output impedance
Dark noise
OB difference in level
1. T
2. The average output voltage under uniform illumination.
3. The image area is divided into 10 x 10 segments under
4. The image area is divided into 10 x 10 segments. Each
5. The average output voltage under non-exposure
6. The image area is divided into 10 x 10 segments under
• V
A
that ABL satisfy the specification, or to the value
displayed on the device.
The standard exposure conditions are defined as when
Vo is 150 mV.
the standard exposure conditions. Each segment's
voltage is the average output voltage of all pixels within
the segment. PRNU is defined by (Vmax – Vmin)/Vo,
where Vmax and Vmin are the maximum and minimum
values of each segment's voltage respectively.
segment's voltage is the average output voltage of all
pixels within the segment. V
segment's voltage under 10 times exposure of the
standard exposure conditions.
conditions.
non-exposure conditions. DSNU is defined by (Vdmax –
Vdmin), where Vdmax and Vdmin are the maximum and
minimum values of each segment's voltage respectively.
= +25 ˚C, Operating conditions : The typical values specified in "RECOMMENDED OPERATING CONDITIONS".
A
OFD
= +60 ˚C
should be adjusted to the minimum voltage such
PARAMETER
SAT
is the minimum
(Drive method : Field accumulation)
SYMBOL
5
V
PRNU
V
DSNU
V
SMR
ABL
NOISE
DARK
I
V
R
AI
OD
SAT
R
‹
O
10. The sensor is exposed only in the central area of V/10
11. The RMS value of the dark noise after CDS. (100 kHz to
12. The difference between the average output voltage of
O
7. The average output voltage when a 1 000 lux light
8. The sensor is exposed only in the central area of V/10
9. The sensor is exposed at the exposure level
source with a 90% reflector is imaged by a lens of F4,
f50 mm.
square with a lens at F4, where V is the vertical image
size. SMR is defined by the ratio of the output voltage
detected during the vertical blanking period to the
maximum output voltage in the V/10 square.
corresponding to the standard conditions. AI is defined
by the ratio of the output voltage measured at the 1st
field during the non-exposure period to the standard
output voltage.
square, where V is the vertical image size. ABL is
defined by the ratio of the exposure at the standard
conditions to the exposure at a point where blooming is
observed.
5.0 MHz, SC trap on.)
the effective area and that of the OB area under non-
exposure conditions.
1 000
MIN.
650
370
TYP.
–84
150
500
350
0.5
0.5
4.0
0.2
1
LZ2363B/LZ2364BJ
MAX.
–76
3.0
2.0
1.0
8.0
0.3
1.0
10
UNIT
mV
mV
mV
mV
mV
mA
mV
mV
dB
%
%
$
NOTE
1, 12
1, 5
1, 6
10
11
2
3
4
7
8
9