X9514 Xicor, X9514 Datasheet
X9514
Available stocks
Related parts for X9514
X9514 Summary of contents
Page 1
... The Xicor X9514 is a push button controlled, logarithmic taper potentiometer and is ideal for push button con- trolled resistance trimming. The X9514 is a resistor array composed of 31 resistive elements. Between each element and at either end are tap points accessible to the wiper element. The position of the wiper element is controlled by the PU and PD inputs ...
Page 2
... V – AUTOSTORE is disabled. A LOW to HIGH will IH initiate a manual store operation. This is for a user who wishes to connect a push button switch to this pin. For every valid push, the X9514 will store the current wiper position to the E 2 PROM. Typical Attenuation Characteristics (dB) 0 ...
Page 3
... At either end of the array and between each resistor is an electronic switch that trans- fers the potential at that point to the wiper. The X9514 is designed to interface directly to two push button switches for effectively moving the wiper up or down. The PU and PD inputs increment or decrement a 5-bit counter respectively ...
Page 4
... Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Temperature Coefficient (– +85 C) X9514W ..................................... +600 ppm/ C Typical Ratiometric Temperature Coefficient ............ 20 ppm Wiper Adjustability Unlimited Wiper Adjustment (Non-Store operation) Wiper Position Store Operations ............. 100,000 Physical Characteristics ) = 0 ...
Page 5
... STANDARD PARTS Part Number Maximum Resistance X9514W Notes: (4) Typical values are for and nominal supply voltage. A (5) This parameter is periodically sampled and not 100% tested. Max. Supply Voltage +70 C X9514 +85 C +125 C 6487 PGM T03.1 Limits (4) Min. Typ. Max. Units 1 ...
Page 6
... X9514 A.C. OPERATING CHARACTERISTICS (Over recommended operating conditions unless otherwise specified) Symbol Parameter t Time Between Two Separate Push Button Events GAP t Debounce Time DB t After Debounce to Wiper Change on a Slow Mode S SLOW S FAST (7) t Wiper Change on a Scan Mode PU (7) t Power Up to Wiper Stable ...
Page 7
... X9514 Slow Mode Timing Notes: ( the A.C. timing diagram refers to the minimum incremental change in the wiper voltage. Fast Mode Timing SLOW V W Notes: ( the A.C. timing diagram refers to the minimum incremental change in the wiper voltage GAP t S FAST ...
Page 8
... X9514 PACKAGING INFORMATION HALF SHOULDER WIDTH ON ALL END PINS OPTIONAL 0.015 (0.38) MAX. TYP. 0.010 (0.25) NOTE: 1. ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 2. PACKAGE DIMENSIONS EXCLUDE MOLDING FLASH 8-LEAD PLASTIC DUAL IN-LINE PACKAGE TYPE P 0.430 (10.92) 0.360 (9.14) PIN 1 INDEX PIN 1 0.300 (7.62) REF. SEATING PLANE 0.150 (3.81) ...
Page 9
... X9514 PACKAGING INFORMATION 8-LEAD PLASTIC SMALL OUTLINE GULL WING PACKAGE TYPE S PIN 1 INDEX 0.010 (0.25) 0.020 (0.50) 0 – 8 0.016 (0.410) 0.037 (0.937) NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 0.150 (3.80) 0.158 (4.00) PIN 1 0.014 (0.35) 0.019 (0.49) 0.188 (4.78) 0.197 (5.00) (4X) 7 0.004 (0.19) 0.050 (1.27) 0.010 (0.25 0.0075 (0.19) 0.250" 0.010 (0.25) ...
Page 10
... X9514 PACKAGING INFORMATION 14-LEAD PLASTIC, TSSOP PACKAGE TYPE V 0 – 8 See Detail “A” NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) .025 (.65) BSC .169 (4.3) .252 (6.4) BSC .177 (4.5) .193 (4.9) .200 (5.1) .047 (1.20) .0075 (.19) .002 (.05) .0118 (.30) .006 (.15) .010 (.25) Gage Plane Seating Plane .019 (.50) .029 (.75) Detail A (20X) ...
Page 11
... X9514 ORDERING INFORMATION X9514X LIMITED WARRANTY Devices sold by Xicor, Inc. are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. Xicor, Inc. makes no warranty, express, statutory, implied description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. ...