AD5426YRM-REEL7 AD [Analog Devices], AD5426YRM-REEL7 Datasheet
AD5426YRM-REEL7
Related parts for AD5426YRM-REEL7
AD5426YRM-REEL7 Summary of contents
Page 1
FEATURES 3 5.5 V Supply Operation 50 MHz Serial Interface 10 MHz Multiplying Bandwidth 10 V Reference Input Low Glitch Energy < 2 nV-s Extended Temperature Range – +125 C 10-Lead MSOP Package Pin Compatible 8-, ...
Page 2
AD5426/AD5432/AD5443–SPECIFICATIONS ( 5 All specifications T DD REF OUT performance with AD8038, unless otherwise noted.) Parameter STATIC PERFORMANCE AD5426 Resolution Relative Accuracy Differential Nonlinearity AD5432 Resolution ...
Page 3
Parameter SFDR Performance (Wide Band) Clock = 10 MHz 50 kHz f OUT 20 kHz f OUT SFDR Performance (Narrow Band) Clock = 1 MHz 50 kHz f OUT 20 kHz f OUT Intermodulation Distortion Clock = 1 MHz f ...
Page 4
AD5426/AD5432/AD5443 TIMING CHARACTERISTICS Parameter 3 5 SCLK ...
Page 5
... Only one absolute maximum rating may be applied at any one time. 2 Transient currents 100 mA will not cause SCR latchup. Overvoltages at SCLK, SYNC, and DIN, will be clamped by internal diodes. 3 Resolution Model (Bit) AD5426YRM 8 AD5426YRM-REEL 8 AD5426YRM-REEL7 8 AD5432YRM 10 AD5432YRM-REEL 10 AD5432YRM-REEL7 10 AD5443YRM 12 AD5443YRM-REEL 12 AD5443YRM-REEL7 ...
Page 6
AD5426/AD5432/AD5443 Pin No. Mnemonic Function DAC Current Output. OUT DAC Analog Ground. This pin should normally be tied to the analog ground of the system. OUT 3 GND Ground Pin. 4 SCLK Serial Clock ...
Page 7
Typical Performance Characteristics–AD5426/AD5432/AD5443 0. 10V 0.15 REF 0.10 0.05 0 –0.05 –0.10 –0.15 –0. 100 150 200 250 CODE TPC 1. INL vs. Code (8-Bit DAC) 0.20 ...
Page 8
AD5426/AD5432/AD5443 2 REF MAX INL AD5443 0.5 MAX DNL 0 –0.5 MIN INL –1.0 MIN DNL –1.5 –2.0 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 ...
Page 9
AD5443 3.0 LOADING 010101010101 2.5 2 100 1k 10k 100k 1M 10M 100M FREQUENCY (Hz) TPC 19. Supply Current vs. ...
Page 10
AD5426/AD5432/AD5443 1 1.6 1 1.2 1 0.8 0.6 0.4 0.2 0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 VOLTAGE (V) TPC 28. Threshold Voltages vs. Supply Voltage ...
Page 11
TERMINOLOGY Relative Accuracy Relative accuracy or endpoint nonlinearity is a measure of the maximum deviation from a straight line passing through the endpoints of the DAC transfer function measured after adjusting for 0 and full scale and is ...
Page 12
AD5426/AD5432/AD5443 DAC SECTION The AD5426, AD5432, and AD5443 are 8-, 10-, and 12-bit cur- rent output DACs consisting of a standard inverting R-2R ladder configuration. A simplified diagram for the 8-bit AD54246 is shown in Figure 4. The feedback resistor ...
Page 13
SYNC Function SYNC is an edge-triggered input that acts as a frame synchroni- zation signal and chip enable. Data can be transferred into the device only while SYNC is low. To start the serial data transfer, SYNC should be taken ...
Page 14
AD5426/AD5432/AD5443 R1 V REF V REF 10V NOTES 1. R1 AND R2 ARE USED ONLY IF GAIN ADJUSTMENT IS REQUIRED. ADJUST R1 FOR V 2. MATCHING AND TRACKING IS ESSENTIAL FOR RESISTOR PAIRS R3 AND R4 PHASE COMPENSATION ...
Page 15
Voltage Switching Mode of Operation Figure 9 shows these DACs operating in the voltage-switching mode. The reference voltage applied to the connected to AGND, and the output voltage is available OUT at ...
Page 16
AD5426/AD5432/AD5443 DAC leakage current is also a potential error source in divider circuits. The leakage current must be counterbalanced by an opposite current supplied from the op amp through the DAC. Since only a fraction D of the current into ...
Page 17
Most single-supply circuits include ground as part of the analog signal range, which in turns requires an amplifier that can handle rail-to-rail signals, there is a large range of single-supply amplifiers available from Analog Devices. MICROPROCESSOR INTERFACING Microprocessor interfacing to ...
Page 18
AD5426/AD5432/AD5443 MC68HC11 Interface to AD5426/AD5432/AD5443 Interface Figure 16 shows an example of a serial interface between the DAC and the MC68HC11 microcontroller. The serial peripheral interface (SPI) on the MC68HC11 is configured for master mode (MSTR = 1), clock polarity ...
Page 19
EVALUATION BOARD FOR THE AD5426/AD5432/AD5443 SERIES OF DACS The board consists of a 12-bit AD5443 and a current to voltage amplifier AD8065. Included on the evaluation board reference ADR01. An external reference may also be applied ...
Page 20
AD5426/AD5432/AD5443 P1 EVAL–AD5426/ AD5432/AD5443EB Figure 20. Silkscreen—Component Side View (Top Layer) Figure 21. Silkscreen—Component Side View (Bottom Layer) SCLK J3 C11 U3 SCLK J1 VOUT SDIN U1 J4 SDIN R1 C6 SYNC VREF LK1 SYNC U2 C3 ...
Page 21
Part No. Resolution No. DACs AD5403 AD5410 AD5413 AD5424 8 1 AD5425 8 1 AD5426 8 1 AD5428 8 2 AD5429 8 2 AD5450 8 1 AD5404 AD5411 AD5414* 10 ...
Page 22
AD5426/AD5432/AD5443 OUTLINE DIMENSIONS 10-Lead Mini Small Outline Package [MSOP] (RM-10) Dimensions shown in millimeters 3.00 BSC 10 6 4.90 BSC 3.00 BSC 1 5 PIN 1 0.50 BSC 0.95 0.85 1.10 MAX 0.75 0.15 0.27 SEATING 0.23 0.00 PLANE 0.17 ...
Page 23
–23– ...
Page 24
–24– ...