PDIUSBH12N PHILIPS [NXP Semiconductors], PDIUSBH12N Datasheet
PDIUSBH12N
Related parts for PDIUSBH12N
PDIUSBH12N Summary of contents
Page 1
PDIUSBH12 USB 2-port hub Product specification Supersedes data of 1999 Feb 25 hilips Semiconductors INTEGRATED CIRCUITS 1999 Jul 22 ...
Page 2
Philips Semiconductors USB 2-port hub FEATURES Complies with the Universal Serial Bus specification Rev. 1.0 Complies with the ACPI, OnNOW, and USB power management requirements Compliant with USB Human Interface Devices and Monitor Control Class Compliant with System Management Bus ...
Page 3
Philips Semiconductors USB 2-port hub BLOCK DIAGRAM UPSTREAM PORT 3.3V D+ 1.5k D+ SoftConnect ANALOG HUB REPEATER ANALOG GOODLINK ANALOG GOODLINK CONTROL CONTROL D– LED D+ D– ...
Page 4
Philips Semiconductors USB 2-port hub Analog Transceivers These transceivers interface directly to the USB cables through some termination resistors. They are capable of transmitting and receiving serial data at both “full speed” (12 Mbit/s) and “low speed” (1.5 Mbit/s) data ...
Page 5
Philips Semiconductors USB 2-port hub ENDPOINT DESCRIPTIONS There are two endpoint configuration modes supported by the PDIUSBH12, the Single Embedded Function mode and the Multiple (3) Embedded Function mode. The Single Embedded Function mode is the default at power up ...
Page 6
Philips Semiconductors USB 2-port hub PINNING The PDIUSBH12 has two modes of operation. The first mode (Mode 0) configures the pins DNx_GL_N for GoodLink second mode (Mode 1) configures the LED pins as per port overcurrent condition pins. An overcurrent ...
Page 7
Philips Semiconductors USB 2-port hub Pin description (MODE 0 – Good Link ) PIN NO. PIN SYMBOL TYPE 1 TEST1 Input 2 TEST2 Input 3 TEST3 Input 4 RESET_N Input 5 GND Power 6 XTAL1 Input 7 XTAL2 Output 8 ...
Page 8
Philips Semiconductors USB 2-port hub Pin description (MODE 1 – Individual Overcurrent) PIN NO PIN SYMBOL TYPE 1 TEST1 Input 2 TEST2 Input 3 TEST3 Input 4 RESET_N Input 5 GND Power 6 XTAL1 Input 7 XTAL2 Output 8 CLKOUT ...
Page 9
Philips Semiconductors USB 2-port hub APPLICATION DIAGRAM 3.3V 5V POWER SWITCH AND OVERCURRENT CIRCUIT Interface 2 The I C bus is used to interface to an external microcontroller needed to control the operation of the hub. For ...
Page 10
Philips Semiconductors USB 2-port hub COMMAND SUMMARY Some commands have the same command code (e.g., Read Buffer and Write Buffer). In these cases, the direction of the Data Phase (read or write) indicates which command is executed. COMMAND NAME Set ...
Page 11
Philips Semiconductors USB 2-port hub COMMAND DESCRIPTIONS Command Procedure There are four basic types of commands: Initialization, Data, Hub Specific, and General commands. Respectively, these are used to initialize the hub and embedded function; for data flow between the hub, ...
Page 12
Philips Semiconductors USB 2-port hub Configuration Byte POWER ON VALUE REMOTE WAKEUP NO LAZYCLOCK CLOCK RUNNING DEBUG MODE SoftConnect CONNECT DOWNSTREAM RESISTORS NON-BLINKING LEDs ...
Page 13
Philips Semiconductors USB 2-port hub Data Flow Commands Data flow commands are used to manage the data transmission between the USB endpoints and the monitor. Much of the data flow is initiated via an interrupt to the microcontroller. The microcontroller ...
Page 14
Philips Semiconductors USB 2-port hub Table 3. Error codes ERROR RESULT CODE 0000 No Error PID encoding Error; bits 7–4 are not the inversion of 0001 bits 3–0 PID unknown; encoding is valid, but PID does not 0010 exist Unexpected ...
Page 15
Philips Semiconductors USB 2-port hub Set Endpoint Status Command : 40–4Dh Data : Write 1 byte A stalled control endpoint is automatically unstalled when it receives a SETUP token, regardless of the content of the packet. If the endpoint should ...
Page 16
Philips Semiconductors USB 2-port hub Get Port Status Command : E0h–E1h Data : Read bytes The Get Port Status Command can be followed by one or two data reads. The first byte returned contains the port status. ...
Page 17
Philips Semiconductors USB 2-port hub General Commands Send Resume Command : F6h Data : None Sends an upstream resume signal for 10 ms. This command is normally issued when the device is in suspend. The RESUME command is not followed ...
Page 18
Philips Semiconductors USB 2-port hub RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER V DC supply voltage input voltage range input voltage range for I/O I input voltage range for analog I/O AI ...
Page 19
Philips Semiconductors USB 2-port hub DC CHARACTERISTICS (Digital pins) SYMBOL PARAMETER Input Levels V LOW level input voltage IL HIGH level input voltage VIH V LOW to HIGH threshold voltage TLH V HIGH to LOW threshold voltage THL V Hysteresis ...
Page 20
Philips Semiconductors USB 2-port hub AC CHARACTERISTICS (AI/O pins, FULL speed) SYMBOL PARAMETER Driver characteristics Transition Time: t Rise time r t Fall time f t Rise/fall time matching RFM V Output signal crossover voltage CRS Driver Timings t Source ...
Page 21
Philips Semiconductors USB 2-port hub AC CHARACTERISTICS (AI/O pins, LOW speed) SYMBOL PARAMETER Driver characteristics Transition Time t t Rise time Rise time Fall time Fall time Rise/fall time matching RFM V Output signal ...
Page 22
Philips Semiconductors USB 2-port hub V DD CROSSOVER POINT UPSTREAM- DIFFERENTIAL DATA V SS Hub Delay DOWNSTREAM- Downstream DIFFERENTIAL t DATA HDD DOWNSTREAM HUB DELAY SOP DISTORTION (SOP) – t (NEXT J) SOP HDD ...
Page 23
Philips Semiconductors USB 2-port hub 2 AC CHARACTERISTICS (I C pins) All timing values are valid within the operating supply voltage and ambient temperature range and reference to V swing of V and SYMBOL PARAMETER f ...
Page 24
Philips Semiconductors USB 2-port hub SO28: plastic small outline package; 28 leads; body width 7.5mm 1999 Jul 22 24 Product specification PDIUSBH12 SOT136-1 ...
Page 25
Philips Semiconductors USB 2-port hub DIP28: plastic dual in-line package; 28 leads (600 mil) 1999 Jul 22 25 Product specification PDIUSBH12 SOT117-1 ...
Page 26
Philips Semiconductors USB 2-port hub SOLDERING Introduction This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our “Data Handbook IC26; Integrated Circuit Packages” (document order number 9398 ...
Page 27
Philips Semiconductors USB 2-port hub SUITABILITY OF IC PACKAGES FOR WAVE, REFLOW AND DIPPING SOLDERING METHODS Mo nting Mounting Package Package Through-hole mount DBS, DIP, HDIP, SDIP, SIL BGA, SQFP, HLQFP, HSQFP, HSOP, SMS Surface mount PLCC, SO, SOJ LQFP, ...
Page 28
Philips Semiconductors USB 2-port hub Data sheet status Data sheet Product Definition status status Objective Development This data sheet contains the design target or goal specifications for product development. specification Specification may change in any manner without notice. Preliminary Qualification ...