OPA4705EA BURR-BROWN [Burr-Brown Corporation], OPA4705EA Datasheet - Page 2

• Manufacturer Part Number: OPA4705EA
• Description: Low-Cost, CMOS, Rail-to-Rail, I/O OPERATIONAL AMPLIFIERS
• Manufacturer: BURR-BROWN [Burr-Brown Corporation]

NOTES: (1) Stresses above these ratings may cause permanent damage.
Exposure to absolute maximum conditions for extended periods may
degrade device reliability. (2) Input terminals are diode-clamped to the power
supply rails. Input signals that can swing more than 0.3V beyond the supply
rails should be current-limited to 10mA or less. (3) Short-circuit to ground,
one amplifier per package.
NOTE: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /3K indicates 3000 devices per reel). Ordering 3000 pieces
of “OPA705NA/3K” will get a single 3000-piece Tape and Reel.
2
ABSOLUTE MAXIMUM RATINGS
PACKAGE/ORDERING INFORMATION
Supply Voltage, V+ to V– ................................................................. 13.2V
Signal Input Terminals, Voltage
Output Short-Circuit
Operating Temperature .................................................. –55 C to +125 C
Storage Temperature ..................................................... –65 C to +150 C
Junction Temperature .................................................................... +150 C
Lead Temperature (soldering, 10s) ............................................... +300 C
PRODUCT
OPA705NA
OPA705UA
OPA705PA
OPA2705EA
OPA2705UA
OPA2705PA
OPA4705EA
OPA4705UA
"
"
"
"
"
"
Single, GBW = 1MHz
Single, GBW = 1MHz
Single, GBW = 1MHz
Quad, GBW = 1MHz
(3)
Quad, GBW = 1MHz
Dual, GBW = 1MHz
Dual, GBW = 1MHz
Dual, GBW = 1MHz
.............................................................. Continuous
DESCRIPTION
Current
"
"
"
"
"
"
(2)
(2)
..................... (V–) –0.3V to (V+) +0.3V
.................................................... 10mA
RECOMMENDED
(1)
MINIMUM
GAIN
1
1
1
1
1
1
1
1
"
"
"
"
"
"
PACKAGE
TSSOP-14
SOT23-5
MSOP-8
SO-14
DIP-8
DIP-8
SO-8
SO-8
"
"
"
"
"
"
This integrated circuit can be damaged by ESD. Texas Instru-
ments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
ESD damage can range from subtle performance degrada-
tion to complete device failure. Precision integrated circuits
may be more susceptible to damage because very small
parametric changes could cause the device not to meet its
published specifications.
PACKAGE
DRAWING
NUMBER
331
182
006
337
182
006
357
235
"
"
"
"
"
"
ELECTROSTATIC
DISCHARGE SENSITIVITY
OPA2705UA
OPA2705PA
OPA4705EA
OPA4705UA
OPA705UA
OPA705PA
PACKAGE
MARKING
A05
B05
"
"
"
"
"
"
OPA2705EA/2K5
OPA2705UA/2K5
OPA4705EA/2K5
OPA4705UA/2K5
OPA2705EA/250
OPA4705EA/250
OPA705UA/2K5
OPA705NA/250
OPA705NA/3K
OPA2705UA
OPA2705PA
OPA4705UA
ORDERING
NUMBER
OPA705UA
OPA705PA
OPA705, 2705, 4705
(1)
SBOS182A
Tape and Reel
Tape and Reel
Tape and Reel
Tape and Reel
Tape and Reel
Tape and Reel
Tape and Reel
Tape and Reel
Tape and Reel
TRANSPORT
MEDIA
Rails
Rails
Rails
Rails
Rails