HCPL-2300300 HP [Agilent(Hewlett-Packard)], HCPL-2300300 Datasheet - Page 5

• Manufacturer Part Number: HCPL-2300300
• Description: 8 MBd Low Input Current Optocoupler
• Manufacturer: HP [Agilent(Hewlett-Packard)]

Absolute Maximum Ratings
(No Derating Required up to 55 C)
Storage Temperature, T
Operating Temperature, T
Lead Solder Temperature, max .......................................... 260 C for 10 s
Average Forward Input Current - I
Reverse Input Voltage, V
Supply Voltage, V
Pull-Up Resistor Voltage, V
Output Collector Current, I
Input Power Dissipation, P
Output Collector Power Dissipation, P
Output Collector Voltage, V
Infrared and Vapor Phase Reflow Temperature
1-292
Recommended Operating Conditions
VDE 0884 Insulation Related Characteristics (HCPL-2300 Option 060 ONLY)
*Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section, (VDE 0884), for a
detailed description.
Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in
application.
Input Voltage, Low Level
Input Current High Level
Supply Voltage, Output
Fan Out (TTL Load)
Operating Temperature
Installation classification per DIN VDE 0110/1.89, Table 1
Climatic Classification
Pollution Degree (DIN VDE 0110/1.89)
Maximum Working Insulation Voltage
Input to Output Test Voltage, Method b*
Input to Output Test Voltage, Method a*
Highest Allowable Overvoltage*
(Transient Overvoltage, t
Safety Limiting Values
Insulation Resistance at T
(Option #300) .......................................... see Fig. 1, Thermal Profile
for rated mains voltage
for rated mains voltage
V
Partial Discharge < 5 pC
V
Partial Discharge < 5 pC
(Maximum values allowed in the event of a failure,
also see Figure 11, Thermal Derating curve.)
IORM
IORM
Case Temperature
Input Current
Output Power
x 1.875 = V
x 1.5 = V
CC
............................................................... 0 V to 7.0 V
Parameter
PR
, Type and sample test, t
PR
S
R
, 100% Production Test with t
............................................. -55 C to +125 C
A
.............................................................. 3.0 V
RL
O
O
I
ini
........................................... -40 C to +85 C
S
........................................................ 10 mW
............................................ -25 to 25 mA
, V
............................................. -0.5 V to V
........................................... -0.5 V to 18 V
Description
= 10 sec)
300 V rms
450 V rms
IO
= 500 V
F
............................................ 5 mA
0 C to 85 C
-40 C to 85 C
O
..................................... 40 mW
(1.6 mm below seating plane)
m
= 60 sec,
m
= 1 sec,
Symbol
V
V
I
T
N
FH
CC
FL
A
[2]
CC
P
Symbol
I
S,OUTPUT
V
V
S,INPUT
V
V
IORM
IOTM
R
Min.
T
4.75
-2.5
-40
PR
PR
0.5
0.5
S
S
Characteristic
55/85/21
Max.
0.75
5.25
0.8
1.0
85
1181
6000
5
630
945
175
230
600
I-IV
I-III
10
2
9
Units
mA
Units
V
V
V
V
V
V
C
mW
mA
peak
peak
peak
peak
C