ADL5513-ACPZ-R2 AD [Analog Devices], ADL5513-ACPZ-R2 Datasheet

ADL5513-ACPZ-R2

Manufacturer Part Number

ADL5513-ACPZ-R2

Description

1 MHz to 4 GHz, 80 dB Logarithmic Detector/Controller

Manufacturer

AD [Analog Devices]

Datasheet

1.ADL5513-ACPZ-R2.pdf (12 pages)

Current page: 1 of 12
Download datasheet (2Mb)

Preliminary Technical Data

FEATURES

Wide bandwidth: 1 MHz to 4 GHz

80 dB dynamic range (±3 dB)

Stability over temperature: < ±0.5 dB

Low noise measurement/controller output (VOUT)

Pulse response time: 10 ns

Small footprint package: 3 mm x 3 mm LFCSP

Supply operation: 2.7 to 5.5 V at 30 mA

Fabricated using high speed SiGe process

APPLICATIONS

RF transmitter PA setpoint control and level monitoring

Power monitoring in radiolink transmitters

RSSI measurement in base stations, WLAN, WiMAX, radar

GENERAL DESCRIPTION

The ADL5513 is a demodulating logarithmic amplifier, capable

of accurately converting an RF input signal to a corresponding

decibel-scaled output. It employs the progressive compression

technique over a cascaded amplifier chain, each stage of which

is equipped with a detector cell. The device can be used in

either measurement or controller modes. The ADL5513

maintains accurate log conformance for signals greater than 4

GHz. The input dynamic range is typically 80 dB (re: 50 Ω)

with error less than ±3 dB. The ADL5513 has 10 ns response

time which enables RF burst detection to a pulse rate of beyond

50 MHz. The device provides unprecedented logarithmic

intercept stability vs. ambient temperature conditions. A supply

of 2.7 V to 5.5 V is required to power the device. Current

consumption is less than 30 mA, and decreases to TBD μA

when the device is disabled.

The ADL5513 can be configured to provide a control voltage to

a power amplifier or a measurement output from the VOUT

Rev. PrA 6/08

Information furnished by Analog Devices is believed to be accurate and reliable. However, no

responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other

rights of third parties that may result from its use. Specifications subject to change without notice. No

license is granted by implication or otherwise under any patent or patent rights of Analog Devices.

Trademarks and registered trademarks are the property of their respective owners.

Logarithmic Detector/Controller

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.

Tel: 781.329.4700

Fax: 781.461.3113

V P OS

pin. Because the output can be used for controller applications,

special attention has been paid to minimize wideband noise. In

this mode, the setpoint control voltage is applied to the VSET

pin.

The feedback loop through an RF amplifier is closed via VOUT,

the output of which regulates the amplifier’s output to a

magnitude corresponding to V

to (V

controller applications. As a measurement device, VOUT is

externally connected to VSET to produce an output voltage

The logarithmic slope is 20 mV/dB, determined by the VSET

interface. The intercept is -95 dBm (re: 50 Ω, CW input, 900

MHz) using the INHI input. These parameters are very stable

against supply and temperature variations.

IN LO

IN HI

OUT

POS

that increases linear-in-dB with RF input signal amplitude.

DET

− 0.1 V) output capability at the VOUT pin, suitable for

FUNCTIONAL BLOCK DIAGRAM

DET

CO NT RO L

S L O P E

1 MHz to 4 GHz, 80 dB

AD L5513

DET

Figure 1.

RE FE RENC E

BA N D G AP

SET

DET

. The ADL5513 provides 0 V

DET

G AIN

BIAS

ADL5513

www.analog.com

VO UT

V S E T

COMM

TADJ

Related parts for ADL5513-ACPZ-R2

Related keywords

ADL5513-ACPZ-R2 datasheet
ADL5513-ACPZ-R2 data sheet
ADL5513-ACPZ-R2 pdf datasheet
ADL5513-ACPZ-R2 component
ADL5513-ACPZ-R2 part
ADL5513-ACPZ-R2 distributor
ADL5513-ACPZ-R2 RoHS
ADL5513-ACPZ-R2 datasheet download