ALD4706A ALD [Advanced Linear Devices], ALD4706A Datasheet - Page 4

• Manufacturer Part Number: ALD4706A
• Description: DUAL ULTRA MICROPOWER RAIL-TO-RAIL CMOS OPERATIONAL AMPLIFIER
• Manufacturer: ALD [Advanced Linear Devices]

ALD4706A/ALD4706B
ALD4706
Design & Operating Notes:
1. The ALD4706A/ALD4706B/ALD4706 CMOS operational amplifier
2. The ALD4706A/ALD4706B/ALD4706 has complementary p-channel
3.
uses a 3 gain stage architecture and an improved frequency
compensation scheme to achieve large voltage gain, high output
driving capability, and better frequency stability. In a conventional
CMOS operational amplifier design, compensation is achieved with
a pole splitting capacitor together with a nulling resistor. This method
is, however, very bias dependent and thus cannot accommodate the
large range of supply voltage operation as is required from a stand
alone CMOS operational amplifier. The ALD4706A/ALD4706B/
ALD4706 is internally compensated for unity gain stability using a
novel scheme that does not use a nulling resistor. This scheme
produces a clean single pole roll off in the gain characteristics while
providing for more than 70 degrees of phase margin at the unity gain
frequency.
and n-channel input differential stages connected in parallel to
accomplish rail to rail input common mode voltage range. This means
that with the ranges of common mode input voltage close to the power
supplies, one of the two differential stages is switched off internally.
To maintain compatibility with other operational amplifiers, this
switching point has been selected to be about 1.5V below the positive
supply voltage. Since offset voltage trimming on the ALD4706A/
ALD4706B/ALD4706 is made when the input voltage is symmetrical
to the supply voltages, this internal switching does not affect a large
variety of applications such as an inverting amplifier or non-inverting
amplifier with a gain larger than 2.5 (5V operation), where the common
mode voltage does not make excursions above this switching point.
The user should however, be aware that this switching does take
place if the operational amplifier is connected as a unity gain buffer
and should make provision in his design to allow for input offset voltage
variations.
diode reverse bias leakage currents, and are typically less than 0.1pA
The input bias and offset currents are essentially input protection
320
160
1000
240
100
80
10
0
1
10K
0
INPUTS GROUNDED
OUTPUT UNLOADED
SUPPLY CURRENT AS A FUNCTION
OPEN LOOP VOLTAGE GAIN AS A
FUNCTION OF LOAD RESISTANCE
±1
OF SUPPLY VOLTAGE
SUPPLY VOLTAGE (V)
T
100K
±2
LOAD RESISTANCE (Ω)
A
= -55°C
TYPICAL PERFORMANCE CHARACTERISTICS
±3
-25°C
+70°C
1M
±4
+25°C
V
T
S
A
+125°C
±5
= ±2.5V
= 25°C
Advanced Linear Devices
10M
±6
4. The output stage consists of class AB complementary output drivers,
5. The ALD4706A/ALD4706B/ALD4706 operational amplifier has been
6. The ALD4706A/ALD4706B/ALD4706, with its ultra micropower
at room temperature. This low input bias current assures that the
analog signal from the source will not be distorted by input bias
currents. Normally, this extremely high input impedance of greater
than 10
limit the node impedance. However, for applications where source
impedance is very high, it may be necessary to limit noise and hum
pickup through proper shielding.
capable of driving a low resistance load. The output voltage swing is
limited by the drain to source on-resistance of the output transistors
as determined by the bias circuitry, and the value of the load resistor.
When connected in the voltage follower configuration, the oscillation
resistant feature, combined with the rail to rail input and output feature,
makes an effective analog signal buffer for medium to high source
impedance sensors, transducers, and other circuit networks.
designed to provide full static discharge protection. Internally, the
design has been carefully implemented to minimize latch up.
However, care must be exercised when handling the device to avoid
strong static fields that may degrade a diode junction, causing
increased input leakage currents. In using the operational amplifier,
the user is advised to power up the circuit before, or simultaneously
with, any input voltages applied and to limit input voltages to not
exceed 0.3V of the power supply voltage levels.
operation, offers numerous benefits in reduced power supply
requirements, less noise coupling and current spikes, less thermally
induced drift, better overall reliability due to lower self heating, and
lower input bias current. It requires practically no warm up time as
the chip junction heats up to only 0.1°C above ambient temperature
under most operating conditions.
10000
1000
100
1.0
0.1
±7
±6
±5
±4
±3
±2
±1
10
13
0
Ω would not be a problem as the source impedance would
-50
COMMON MODE INPUT VOLTAGE RANGE
0
AS A FUNCTION OF SUPPLY VOLTAGE
INPUT BIAS CURRENT AS A FUNCTION
-25
±1
V
T
OF AMBIENT TEMPERATURE
S
A
= ±2.5V
= 25°C
AMBIENT TEMPERATURE (°C)
±2
0
SUPPLY VOLTAGE (V)
±3
25
±4
50
±5
75
±6
100
±7
125
4 of 9