TC74HC123AP(NEW) Toshiba, TC74HC123AP(NEW) Datasheet

IC MULTIVIBRATOR DL/MONO 16DIP

TC74HC123AP(NEW)

Manufacturer Part Number
TC74HC123AP(NEW)
Description
IC MULTIVIBRATOR DL/MONO 16DIP
Manufacturer
Toshiba
Series
74HCr
Datasheet

Specifications of TC74HC123AP(NEW)

Logic Type
Monostable
Independent Circuits
2
Schmitt Trigger Input
Yes
Propagation Delay
16ns
Current - Output High, Low
5.2mA, 5.2mA
Voltage - Supply
2 V ~ 6 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Through Hole
Package / Case
16-DIP (0.300", 7.62mm)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
TC74HC123AP
TC74HC123AP9(NEW)
Dual Retriggerable Monostable Multivibrator
MULTIVIBRATOR fabricated with silicon gate C
technology.
LSTTL while maintaining the CMOS low power dissipation.
input (positive edge). These inputs are valid for a slow rise/fall
time signal (tr = tf = 1 s) as they are schmitt trigger inputs. This
device may also be triggered by using CLR input (positive
edge).
a time period determined by the external resistor and capacitor
(Rx, Cx ). A low level at the CLR input breaks this state. In the
MONOSTABLE state, if a new trigger is applied, it extends the
MONOSTABLE period (retrigger mode).
discharge or transient excess voltage.
Features (Note)
The TC74HC123A is a high speed CMOS MONOSTABLE
It achieves the high speed operation similar to equivalent
There are two trigger inputs, A input (negative edge), and B
After triggering, the output stays in a MONOSTABLE state for
Limits for Cx and Rx are:
All inputs are equipped with protection circuits against static
High speed: t
Low power dissipation
High noise immunity: V
Output drive capability: 10 LSTTL loads
Symmetrical output impedance: |I
Balanced propagation delays: t
Wide operating voltage range: V
Pin and function compatible with 74LS123
Note:
External capacitor, Cx: No limit
External resistor, Rx: V
TC74HC123AP,TC74HC123AF,TC74HC123AFN
Standby state: I
Active state: I
In the case of using only one circuit, CLR should be tied to GND, Rx/Cx・Cx・Q・ Q should be tied to OPEN,
the other inputs should be tied to V
pd
= 25 ns (typ.) at V
TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic
CC
CC
V
NIH
= 700 μ A (max) at Ta = 25°C
CC
CC
= 4 μ A (max) at Ta = 25°C
= 2.0 V more than 5 kΩ
≥ 3.0 V more than 1 kΩ
= V
pLH
NIL
CC
CC
OH
∼ − t
(opr) = 2 to 6 V
= 28% V
= 5 V
| = I
pHL
CC
OL
CC
2
or GND.
= 4 mA (min)
MOS
(min)
1
Note: xxxFN (JEDEC SOP) is not available in
Weight
DIP16-P-300-2.54A
SOP16-P-300-1.27A
SOL16-P-150-1.27
TC74HC123AP
TC74HC123AF
TC74HC123AFN
Japan.
TC74HC123AP/AF/AFN
: 1.00 g (typ.)
: 0.18 g (typ.)
: 0.13 g (typ.)
2007-10-01

Related parts for TC74HC123AP(NEW)

TC74HC123AP(NEW) Summary of contents

Page 1

... TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC74HC123AP,TC74HC123AF,TC74HC123AFN Dual Retriggerable Monostable Multivibrator The TC74HC123A is a high speed CMOS MONOSTABLE MULTIVIBRATOR fabricated with silicon gate C technology. It achieves the high speed operation similar to equivalent LSTTL while maintaining the CMOS low power dissipation. There are two trigger inputs, A input (negative edge), and B input (positive edge) ...

Page 2

Pin Assignment IEC Logic Symbol TC74HC123AP/AF/AFN 2 2007-10-01 ...

Page 3

Block Diagram (Note 1)(Note 2) Note 1: Cx, Rx, Dx are external capacitor, resistor, and diode, respectively. Note 2: External clamping diode, Dx; The external capacitor is charged the supply voltage is turned off discharges ...

Page 4

System Diagram CLR Timing Chart V ref F TC74HC123AP/AF/AFN V ref ...

Page 5

Functional Description (1) Stand-by state The external capacitor (Cx) is fully charged to V triggering, the Q and Q P comparators that relate to the timing of the output pulse, and two reference voltage supplies turn off. The total supply ...

Page 6

... Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 2: 500 mW in the range − ...

Page 7

Electrical Characteristics DC Characteristics Characteristics Symbol High-level input V IH voltage Low-level input V IL voltage High-level output voltage Low-level output voltage Input leakage I IN current Rx/Cx terminal I ...

Page 8

Timing Requirements (input: t Characteristics Symbol Minimum pulse width Minimum clear width Minimum retrigger time AC Characteristics = 15 pF Characteristics Output transition time Propagation delay time ( Propagation delay time ( ...

Page 9

AC Characteristics = 50 pF, input Characteristics Symbol t TLH Output transition time t THL Propagation delay t pLH time t pHL ( Propagation delay time t pLH ( CLR TRIGGER-Q, t ...

Page 10

Output Pulse Width Constant K – Supply Voltage (typical) t – Cx Characteristics (typ.) WOUT TC74HC123AP/AF/AFN t – V Characteristics (typ 2007-10-01 ...

Page 11

Package Dimensions Weight: 1.00 g (typ.) TC74HC123AP/AF/AFN 11 2007-10-01 ...

Page 12

Package Dimensions Weight: 0.18 g (typ.) TC74HC123AP/AF/AFN 12 2007-10-01 ...

Page 13

Package Dimensions (Note) Note: This package is not available in Japan. Weight: 0.13 g (typ.) TC74HC123AP/AF/AFN 13 2007-10-01 ...

Page 14

... Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. • The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. • ...

Related keywords