1011-267-0605 Deutsch, 1011-267-0605 Datasheet - Page 3

• Manufacturer Part Number: 1011-267-0605
• Description: BACKSHELL, DT, PLUG, 6WAY; Series: DT; Accessory Type: Backshell; For Use With: Deutsch's DT Series; Cable Exit Angle...
• Manufacturer: Deutsch

DT Series Technical Manual
Product Line Overview
Deutsch DTM Series
Deutsch DTM Series of transportation connectors feature a
miniature contact with an enhanced design based on the world
class, field-proven Deutsch “DT Series”.
The DTM is the connector to be used in harsh environmental
applications where reliable signal circuits are critical to operating
performance. Typical applications include on or around the
engine, the transmission and under the hood. In fact, everywhere
data signals or critical electronic circuits go, the field proven
Deutsch design of the DTM will provide reliable peak connector
performance.
The low cost, size 20 contacts terminate AWG 16 to 22 gauge
wire (0.5mm
featuring spring action fingers are protected by a stainless steel
hood. This allows for positive axial alignment while mating and
prevents probe damage during testing.
Thermoplastic housings offer a wide operating temperature
range (-55
peripheral interface seals allow the DTM to withstand moisture
and fluids.
Deutsch DT Series
Deutsch DT Series of environmentally-sealed, connectors are
designed specifically for cable to cable applications on the engine
or transmission, under the hood, on the chassis or in the cab.
Where signal level circuits in harsh environmental conditions,
where even a small degradation in connection may be critical,
the Deutsch DT Series general purpose connectors will provide
the reliability and performance at the lowest cost.
Thermoplastic (-55
seals are used to allow the connector to withstand conditions
of extreme temperature and moisture. The connector may be
employed with either solid-copper crimp type contacts for critical
circuits or budget-minded stamped and formed contacts. In
either selection, the spring action is designed in the socket and
shrouded by a stainless steel hood that provides closed entry for
positive axial alignment during mating, and eliminates probe
damage from occurring. Contact insertion and withdrawal require
no special tools and are retained in locked position by dielectic
fingers, molded as an integral part of the housing. Secondary
locks are assembled at the mating interfaces. If by chance the
secondary locks are not properly seated during assembly, they
will be pressed into locked position during the mating of the
connector.
4
0
2
C to +125
to 1.5mm
0
C to + 125
2
). Closed entry socket (female) contacts
0
C). Silicone rear wire and internal
0
C rated) housings and silicone
A
STEP
Deutsch DTP Series
Building on both the DT and DTM design strengths, the DTP
connector line was developed to fill the need for higher amperage,
multi-pin, inexpensive connectors. The series meets the same
specifications as the DTM and DT but offers the designer the ability
to use multiple 12 gauge contacts, each with a 25 amp continuous
capacity, within a single shell.
Based on the DTM overall design, it offers the protected interfacial
seal located within the receptacle shell. Standard multi-seal grommet
is used in both the plug and receptacle. Currently available in two and
four pin configurations.
Deutsch DT Bussed Series
These standard “DT” receptacle shells feature internal pin type
contact buss bar arrangements that allow common connections
from 3 to 12 size 16 contacts. Buss bars are available in standard
nickel or gold to match common Deutsch Industrial contacts.
Other features include the use of standard “DT” plugs to mate
with these environmental receptacles. Plugs with any Deutsch
modification are intermatable.
Deutsch DTHD Series
Deutsch developed the DTHD Series for those applications requiring a
complete, environmentally sealed, single power circuit termination.
DTHD plugs and receptacles can be permanently assembled with
thermoplastic end caps that prevent removal of the silicone wire
seal grommets. Designed for diesel engine, electronic fuel injectors,
automatic transmissions, ABS brakes and other applications that
involve fuel and oil exposure. These end caps provide the additional
reliability required for critical wiring circuits.
AHEAD
DT Series Technical Manual
Plug/Receptacle
Shell:
Wedge:
Grommet:
Contacts
Pin:
Socket:
Finish:
Sealing Plugs
Thermoplastic: (All sizes)
Dielectric Withstanding Voltage
Current leakage less than 2 milliamps at 1500 VAC
Insulation Resistance:
1000 megohms minimum at 25
Current Rating
Submersion:
Properly wired and mated connection will withstand immersion under
three feet of water without loss of electronic qualities or leakage.
Fluid Resistance:
Connectors show no damage when exposed to most fluids used in
industrial applications.
Vibration:
No unlocking or unmating and exhibits no mechanical or physical
damage after sinusoidal vibration levels of 20 G’s at 10 to 2000
Hz in each of the three mutually perpendicular planes. No electrical
discontinuities longer than 1 microsecond.
Temperature:
Operative at temperatures from -55
current.
Contact Retention:
Contacts withstand a minimum load of:
MATERIAL SPECIFICATIONS
GENERAL SPECIFICATIONS
Size 20: 7.5 amps
Size 16: 13 amps
Size 12: 25 amps
Size 8: 60 amps
Size 4: 100 amps
20 lbs (89N) for size 20
25 lbs (111N) for size 16
30 lbs (133N) for size 12
35 lbs (156N) for size 8
35 lbs (156N) for size 4
Thermoplastic
Thermoplastic
Silicone Rubber
Copper Alloy
Copper Alloy
Nickel (optional - gold) Plated
(Contact current rating @ 125
0
C.
0
C to +125
A
0
C. Continuous at rated
STEP
0
C (continuous)
AHEAD
Thermal Cycle:
No cracking, chipping or leaking after 20 test cycles from
-55
Durability:
No electrical or mechanical defects after 100 cycles of
engagement and disengagement.
CONTACT
CONTACT SIZE
0
SIZE
20
12
C to +125
16
8
4
#20
#16
#12
#8
#4
WIRE GAUGE
AWG(mm
10 (5.60)
16 (1.0)
18 (.80)
6 (13.0)
20 (.50)
18 (.80)
20 (.50)
16 (1.0)
14 (2.0)
14 (2.0)
12 (3.0)
8 (8.60)
CONTACT RESISTANCE
WIRE SEALING RANGE
0
C.
2
)
RECOMMENDED WIRE INSULATION O.D.
Test Current
(Amps)
(1.35-3.05)
(2.24-3.68)
(3.40-4.32)
(4.83-6.10)
(7.11-7.42)
.053-.120
.088-.145
.134-.170
100
.190-.240
.280-.292
7.5
7.5
7.5
7.5
10
13
13
18
25
60
60
N-SEAL
Resistance (mV)
Solids
60
60
60
60
60
60
60
60
60
60
60
60
(1.35-3.05)
(2.46-4.01 )
.053-.120
.097-.158
Stamped & Formed
E-SEAL
Resistance (mV)
N/A
N/A
N/A
100
100
100
100
100
100
100
100
100
N/A
N/A
N/A
5