CM105CG331J50AT AVX, CM105CG331J50AT Datasheet - Page 11

• Manufacturer Part Number: CM105CG331J50AT
• Description: Cap 330pF 50VDC C0G 5% SMD 0603 T/R
• Manufacturer: AVX

Test Conditions and Specifications for High Dielectric Type (X5R, X7R, Y5V)
∗1
∗2
∗3
∗4
∗5
∗6
∗7
∗8
∗9
Capacitance Value
tanδ (%)
Insulation resistance (IR)
Dielectric resistance
Appearance
Termination strength
Bending strength test
Vibration
test
Soldering
heat
resistance
Solderability
Temperature
cycle
Load
humidity
test
High−
temperature
with
loading
Multilayer Ceramic Chip Capacitors
Test Conditions and Standards
Use 1.5 times when the rated voltage is 250V or over.
Use 1.2 times when the rated voltage is 630V or over.
X7R 16V/ 25V type.
Apply to X5R16V/ 25V type, X7R 6.3V/ 10V type.
Apply to Y5V 16V type, CM32Y5V335 to 106 (25V Type).
Apply to Y5V 6.3V/ 10V type. Apply 16% max. to CM21Y5V106/ CM316Y5V226.
Exclude CT series with thickness of less than 0.66mm and CA series.
Use 1.5 times when the rated voltage is 4V/ 6.3V/ 10V/ 250V and 100V (32X7R474/
43X7R105/ 55X7R105).
Use 1.2 times when the rated voltage is 630V or over.
Keep specimen at 150°C+0/ −10°C for one hour, leave specimen at room ambient
for 48±4 hours.
Apply the same test condition for one hour, then leave the specimen at room ambi-
ent for 48±4 hours.
(∗11)
Test Items
Appearance
∆C
tanδ (%)
Appearance
∆C
tanδ (%)
IR
Withstand voltage
Appearance
∆C
tanδ (%)
IR
Withstand voltage
Appearance
∆C
tanδ (%)
IR
Appearance
∆C
tanδ (%)
IR
(∗15)
(∗15)
(∗15)
(∗15)
(∗15)
(∗6)
(∗6)
(∗15)
(∗15)
(∗15)
Within tolerance
10,000MΩ or 500MΩ
No problem observed
No problem observed
No problem observed
No problem observed at 1mm bent
No significant change is detected
Within tolerance
Satisfies the initial value
No significant change is detected
Satisfies the initial value
10,000MΩ or 500MΩ
Resists without problem
Ni/ Br termination: 90% min.
No significant change is detected
Satisfies the initial value
10,000MΩ or 500MΩ
Resists without problem
No significant change is detected
500MΩ or 25MΩ
No significant change is detected
1,000MΩ or 50MΩ
2.5% max., 3.5% max.
200% max. of initial value
200% max. of initial value
5.0% max.
Within ±12.5%
Within ±12.5%
Within ±7.5%
Within ±7.5%
X7R/ X5R
(∗3)
, 7.5% max.
(∗2)
•
µF min., whichever is smaller
, 7.0% max.
•
µF min., whichever is smaller
•
•
•
µF min., whichever is less
µF min., whichever is smaller
µF min., whichever is smaller
(∗17)
Specifications
(∗12)
9.0% max.
150% max. of initial value
150% max. of initial value
5.0% max., 7.0% max.
∗10
∗11
∗12
∗13
∗14
∗15
∗16
∗17
∗ The above test conditions and standards do not apply to products with optional specifications.
Within ±20%
Within ±20%
Within ±30%
Within ±30%
(∗4)
For the CF series over 630V, apply 500V for 1 minute at room ambient.
Except CF series.
Apply to X5R 10V type.
Apply to 25V series of CM105Y5V154 over, CM21Y5V105 over, 316Y5V155 over.
Measurement condition 1kHz, 1Vrms for Y5V, C<47µF type.
The charge/ discharge current of the capacitor must not exceed 50mA.
2N at 0201 Size
Apply to X5R 4V and 6.3V type.
Y5V
, 12.5% max.
(∗13)
(∗5)
Do previous treatment
Measured after the rated voltage is applied for 2 minutes
at normal room temperature and humidity.
(∗1)
Microscope (10×magnification)
Apply a sideward force of 500g (5N)
PCB−mounted sample.
Glass epoxy PCB (∗03, 05 type and CA Series: T=0.8mm);
fulcrum Spacing: 90mm; for 10 seconds.
Vibration frequency: 10 to 55 (Hz)
Amplitude: 1.5mm
Sweeping condition: 10→55→10Hz/ min.
In X, Y and Z directions:
2 hours each Total 6 hours
Do previous treatment
Soak the sample in 260°C±5°C
solder for 10±0.5 seconds
and place in a room at normal temperature
and humidity; measure after 48±4 hours.
(Preheating Conditions)
Soaking Condition
Do previous treatment
(Cycle)
Normal room temperature (3 min.) →
Lowest operation temperature (30 min.) →
Normal room temperature (3 min.) →
Highest operation temperature (30 min.) →
After five cycles, measure after 48±4hours.
Do previous treatment
After applying rated voltage at
40±2°C and humidty 90 to 95%RH,
for 500+24/ −0 hours and keep at room
condition for 48±4 hours then measure
and check the specification limits.
Do previous treatment
After applying twice
voltage at the highest operating temperature
for 1000+48/ −0 hours, measure the sample
after storing 48±4 hours.
Sn63 Solder
Sn-3Ag-0.5Cu
Capacitance
Order
Apply 2.5 times of the rated voltage for 1 to 5 seconds.
C≤10µF
C>10µF
1
2
Test Conditions
Temperature
150 to 200°C
80 to 100°C
120Hz±10% 0.5±0.2Vrms
1kHz±10%
235±5°C
245±5°C
Fire
(∗7)
(∗8, ∗14)
(∗8)
(∗8)
(∗9)
(∗9)
of the rated
1.0±0.2Vrms
(∗16)
2±0.5 sec.
3±0.5 sec.
2 minutes
2 minutes
(∗10)
to a
Vol
Time