LC51024MV-75F484I Lattice Semiconductor, LC51024MV-75F484I Datasheet - Page 22

• Manufacturer Part Number: LC51024MV-75F484I
• Description: CPLD ispXPLD? 5000MV Family 300K Gates 1024 Macro Cells 200MHz Industrial EECMOS Technology 3.3V 484-Pin FPBGA
• Manufacturer: Lattice Semiconductor

Lattice Semiconductor
Absolute Maximum Ratings
Supply Voltage (V
PLL Supply Voltage (V
Output Supply Voltage (V
IEEE 1149.1 TAP Supply Voltage (V
Input Voltage Applied
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . -65 to 150°C . . . . . . . . . . . . . . . -65 to 150°C
Junction Temperature (T
1. Stress above those listed under the “Absolute Maximum Ratings” may cause permanent damage to the device. Functional
2. Compliance with the Lattice Thermal Management document is required.
3. All voltages referenced to GND.
4. Overshoot and Undershoot of -2V to (V
5. A maximum of 64 I/Os per device with V
Recommended Operating Conditions
E
Hot Socketing Characteristics
V
V
T
I
1. Insensitive to sequence of V
2. 0 ≤ V
3. I
4. LVTTL, LVCMOS only.
Erase/Reprogram Cycle
1. Valid over commercial temperature range.
DK
J
CC
CCP
2
Symbol
operation of the device at these or any other conditions above those indicated in the operational sections of this specification
is not implied (while programming, following the programming specifications).
Symbol
CMOS Erase Reprogram Specifications
rise/fall rates for V
DK
is additive to I
CC
≤ V
Input or I/O Leakage Current
CC
Supply Voltage for 1.8V Devices (ispXPLD 5000MC)
Supply Voltage for 2.5V Devices (ispXPLD 5000MB)
Supply Voltage for 3.3V Devices (ispXPLD 5000MV)
PLL Block Supply Voltage for PLL 1.8V Devices
PLL Block Supply Voltage for PLL 2.5V Devices
PLL Block Supply Voltage for PLL 3.3V Devices
Junction Temperature (Commercial Operation)
Junction Temperature (Industrial Operation)
(MAX), 0 ≤ V
PU
CC
CC
, I
and V
) . . . . . . . . . . . . . . . . . . . . . . . -0.5 to 2.5V . . . . . . . . . . . . . . . . -0.5 to 5.5V
PD
4, 5
CCP
1
or I
Parameter
. . . . . . . . . . . . . . . . . . . . . -0.5 to 5.5V . . . . . . . . . . . . . . . . -0.5 to 5.5V
J
CCO,
CCO
) with Power Applied . . . -55 to 150°C . . . . . . . . . . . . . . . -55 to 150°C
CCO
CC
BH
) . . . . . . . . . . . . . . . . . . -0.5 to 2.5V . . . . . . . . . . . . . . . . -0.5 to 5.5V
. Device defaults to pull-up until non-volatile cells are active.
and V
provided (V
≤ V
) . . . . . . . . . . . . . . . . -0.5 to 4.5V . . . . . . . . . . . . . . . . -0.5 to 4.5V
CCO
CCO
(MAX)
CCJ
when V
IHMAX
Parameter
IN
IN
) . . . . . . . . -0.5 to 4.5V . . . . . . . . . . . . . . . . -0.5 to 4.5V
- V
> 3.6V is allowed.
1, 2, 3
CCO
CCO
+2) volts not to exceed 6V is permitted for a duration of <20ns.
Parameter
1, 2, 3, 4
) ≤ 3.6V.
0 ≤ V
≤ 1.0V. For V
ispXPLD 5000MC
IN
≤ 3.0V
1.8V
Condition
22
CCO
> 1.0V, V
CC
ispXPLD 5000MX Family Data Sheet
min must be present. However, assumes monotonic
Min.
—
ispXPLD 5000MB/V
2.5V/3.3V
1,000
Min.
+/-50
Min.
Typ.
1.65
1.65
2.3
2.3
-40
3
3
0
+/-800
Max.
Max.
Max.
1.95
1.95
105
2.7
3.6
2.7
3.6
—
90
Cycles
Units
Units
Units
μA
V
V
V
V
V
V
C
C