AD7870LP-REEL Analog Devices, AD7870LP-REEL Datasheet

no-image

AD7870LP-REEL

Manufacturer Part Number
AD7870LP-REEL
Description
Manufacturer
Analog Devices
Datasheet
PMIC N/A
DSCC FORM 2233
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
THIS DRAWING IS AVAILABLE
DEPARTMENT OF DEFENSE
APR 97
AND AGENCIES OF THE
LTR
MICROCIRCUIT
A
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
FOR USE BY ALL
STANDARD
DEPARTMENTS
DRAWING
AMSC N/A
Drawing updated to reflect current requirements. - ro
15
A
PREPARED BY
CHECKED BY
APPROVED BY
DRAWING APPROVAL DATE
REVISION LEVEL
REV
SHEET
DAN WONNELL
SANDRA ROONEY
MICHAEL A. FRYE
DESCRIPTION
95-05-08
A
A
1
A
2
REVISIONS
A
3
MICROCIRCUIT, DIGITAL-LINEAR, ANALOG-TO-
DIGITAL CONVERTER, 12-BIT, MONOLITHIC
SILICON
SHEET
A
4
SIZE
A
A
5
DEFENSE SUPPLY CENTER COLUMBUS
A
6
CAGE CODE
67268
COLUMBUS, OHIO 43216
http://www.dscc.dla.mil
A
7
DATE (YR-MO-DA)
1 OF
01-07-10
A
8
15
A
9
10
A
5962-90632
11
A
5962-E515-01
APPROVED
R. MONNIN
12
A
13
A
14
A

Related parts for AD7870LP-REEL

AD7870LP-REEL Summary of contents

Page 1

LTR A Drawing updated to reflect current requirements REV SHEET REV A SHEET 15 REV STATUS REV OF SHEETS SHEET PMIC N/A PREPARED BY DAN WONNELL STANDARD CHECKED BY SANDRA ROONEY MICROCIRCUIT DRAWING APPROVED BY MICHAEL A. FRYE ...

Page 2

SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected ...

Page 3

Absolute maximum ratings. 1/ Positive supply voltage ( AGND ..........................................................-0 +7 Negative supply voltage ( AGND .........................................................+0 -7 AGND to DGND ..............................................................................................-0.3 V ...

Page 4

HANDBOOKS DEPARTMENT OF DEFENSE MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, ...

Page 5

Test Symbol Resolution for which no RES missing codes are guaranteed Integral linearity error ILE Differential linearity error DLE Bipolar zero error BZE Positive full scale error 3/ PFSE Negative full scale error 3/ NFSE Signal to noise ratio 4/ ...

Page 6

TABLE I. Electrical performance characteristics – Continued. Test Symbol Track / hold 5/ t ACQ acquisition time Analog input voltage V IN Analog input current I IN Voltage reference output V REF Voltage reference output dREF/ temperature coefficient dT Reference ...

Page 7

TABLE I. Electrical performance characteristics – Continued. Test Symbol Positive supply current I DD Negative supply current I SS Conversion time t CONV t CONVST pulse width setup pulse width 3 t ...

Page 8

TABLE I. Electrical performance characteristics – Continued. Test Symbol SCLK rising edge SSTRB Bus relinquish time t 14 after SCLK setup BUSY propagation 16 delay Data setup prior to ...

Page 9

Device type Case outlines Terminal number STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 DSCC FORM 2234 APR 97 ...

Page 10

DB11/ DB10/ DB9/ 12 HBEN SCLK SSTRB CLOCK HI 1/ DB11 DB10 DB9 LOW 2/ HI SCLK SSTRB or –5 V LOW 2/ LOW SCLK SSTRB or – single 12-bit parallel word for 16-bit data ...

Page 11

FIGURE 3. Mode 1 timing diagram , (12-bit parallel read). NOTES: 1. Times and External 4.7 k pull-up resistor. 3. External 2 k pull-up resistor, ...

Page 12

FIGURE 3. Mode 2 timing diagram , (12-bit parallel read). NOTES: 1. Times and t are the same for a high byte read as for a low byte read External 4.7 k ...

Page 13

Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change as defined in MIL-PRF-38535, appendix A. 3.9 ...

Page 14

Test requirements Interim electrical parameters (see 4.2) Final electrical parameters (see 4.2) Group A test requirements (see 4.4) Group C end-point electrical parameters (see 4.4) Group D end-point electrical parameters (see 4.4) Group E end-point electrical parameters (see 4.4) 1/ ...

Page 15

Additional criteria for device classes Q and V. The steady-state life test duration, test condition and test temperature, or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The test circuit shall ...

Page 16

... Government assumes no liability whatsoever for any inaccuracies in the information bulletin. DATE: 01-07-10 Standard Vendor CAGE PIN 1/ number 24355 AD7870TQ/883B 24355 AD7870TE/883B Vendor name and address Analog Devices Route 1 Industrial Park P.O. Box 9106 Norwood, MA 02062 Point of contact: Vendor similar PIN 2/ Bay F-1 Raheen Ind. Estate Limerick, Ireland ...

Related keywords