AT25020B-SSHL-B Atmel, AT25020B-SSHL-B Datasheet
AT25020B-SSHL-B
Specifications of AT25020B-SSHL-B
Related parts for AT25020B-SSHL-B
AT25020B-SSHL-B Summary of contents
Page 1
... CC WP Write Protect HOLD Suspends Serial Input SOIC, TSSOP HOLD SCK 3 6 GND 8-lead UDFN, XDFN 8-ball VFBGA HOLD HOLD SCK WP SCK GND Bottom View Bottom View SPI Serial EEPROM 1K (128x8) 2K (256x8) 4K (512x8) AT25010B AT25020B AT25040B GND 5 4 8707B–SEEPR–3/10 ...
Page 2
... Respect to Ground Maximum Operating Voltage.................................... 6.25V DC Output Current ................................................. 5.0 mA Figure 1-1. Block Diagram AT25010B/020B/040B 2 40° 125°C 65° 150° MEMORY ARRAY STATUS 128/256/512 X 8 REGISTER DATA REGISTER MODE DECODE LOGIC CLOCK GENERATOR *NOTICE: Stresses beyond those listed under “ ...
Page 3
Table 1-1. Pin Capacitance Applicable over recommended operating range from T Symbol Test Conditions C Output Capacitance (SO) OUT C Input Capacitance (CS, SCK, SI, WP, HOLD) IN Note: 1. This parameter is characterized and is not 100% tested. ...
Page 4
Table 1-3. AC Characteristics Applicable over recommended operating range from TTL Gate and 30 pF (unless otherwise noted) Symbol Parameter f SCK Clock Frequency SCK t Input Rise Time RI t Input Fall Time FI t ...
Page 5
Table 1-3. AC Characteristics (Continued) Applicable over recommended operating range from TTL Gate and 30 pF (unless otherwise noted) Symbol Parameter t Hold to Output High Output Disable Time DIS t Write Cycle ...
Page 6
Figure 2-1. SPI Serial Interface AT25010B/020B/040B 6 AT25010B/020B/040B 8707B–SEEPR–3/10 ...
Page 7
... Set Write Enable Latch 0000 X100 Reset Write Enable Latch 0000 X101 Read Status Register 0000 X001 Write Status Register 0000 A011 Read Data from Memory Array 0000 A010 Write Data to Memory Array Bit 4 Bit 3 Bit BP1 BP0 Table 3-4. Table 3-4 ...
Page 8
... If the WP pin is brought low or if the device is not write enabled (WREN), the device will ignore the Write instruction and will return to the standby state, when CS is brought high. A new CS falling edge is required to reinitiate the serial communication. AT25010B/020B/040B 8 Array Addresses Protected BP0 AT25010B AT25020B 0 None None ...
Page 9
Timing Diagrams Figure 4-1. Synchronous Data Timing (for Mode CSS V IH SCK HI Figure 4-2. WREN Timing CS SCK ...
Page 10
Figure 4-4. RDSR Timing SCK SI INSTRUCTION HIGH IMPEDANCE SO Figure 4-5. WRSR Timing SCK SI HIGH IMPEDANCE SO Figure 4-6. READ Timing SCK INSTRUCTION SI HIGH IMPEDANCE SO AT25010B/020B/040B ...
Page 11
Figure 4-7. WRITE Timing SCK INSTRUCTION SI HIGH IMPEDANCE SO Figure 4-8. HOLD Timing CS SCK HOLD SO 8707B–SEEPR–3/ ...
Page 12
... Ordering Code Detail Atmel Designator Product Family Device Density 010 = 1k 020 = 2k 040 = 4k Device Revision AT25010B/020B/040B Shipping Carrier Option B or blank = Bulk (tubes Tape and reel Operating Voltage L = 1.8V to 5.5V Package Device Grade or Wafer/Die Thickness H = Green, NiPdAu lead finish, Industrial Temperature Range (-40˚ ...
Page 13
... ATML=ATMEL H=MATERIAL SET/GRADE YWW=DATE CODE LINE 2: 51B=AT25010B, L=1.8 to 5.5v, @=COUNTRY of ORIGIN LINE 3: ATMEL LOT NUMBER AT25010B-XHL PIN 1 INDICATOR(DOT) | |---|---|---|---|---|---| * A T |---|---|---|---|---|---| 5 1 |---|---|---|---|---|---|---| ATMEL LOT NUMBER |---|---|---|---|---|---|---| LINE 1: AT=ATMEL H=MATERIAL SET/GRADE YWW=DATE CODE LINE 2: 51B=AT25010B, L=1.8 to 5.5v, @=COUNTRY of ORIGIN LINE 3: ATMEL LOT NUMBER AT25010B-CUL |---|---|---|---| |---|---|---|---| |---|---|---|---| |<-- PIN 1 THIS CORNER LINE 1: ...
Page 14
... H=MATERIAL SET/GRADE, L=1.8 to 5.5V, @=COUNTRY OF ORIGIN LINE 3: Y=DATE CODE, XX=TRACE CODE AT25010B-MEHL |---|---|---| |---|---|---| |---|---|---| * | PIN 1 INDICATOR (DOT) LINE 1: 51B=AT25010B LINE 2: Y=DATE CODE, XX=TRACE CODE AT25020B-SSHL |---|---|---|---|---|---|---|---| |---|---|---|---|---|---|---|---| |---|---|---|---|---|---|---|---| |---|---|---|---|---|---|---|---| | PIN 1 INDICATOR (DOT) LINE 1: ATML=ATMEL H=MATERIAL SET/GRADE YWW=DATE CODE LINE 2: 52B=AT25020B, L=1.8 to 5.5v, @=COUNTRY of ORIGIN LINE 3: ATMEL LOT NUMBER AT25010B/020B/040B 8707B–SEEPR–3/10 ...
Page 15
... AT25020B-XHL PIN 1 INDICATOR (DOT) | |---|---|---|---|---|---| * A T |---|---|---|---|---|---| 5 2 |---|---|---|---|---|---|---| |---|---|---|---|---|---|---| LINE 1: AT=ATMEL H=MATERIAL SET/GRADE YWW=DATE CODE LINE 2: 52B=AT25020B, L=1.8 to 5.5v, @=COUNTRY of ORIGIN LINE 3: ATMEL LOT NUMBER AT25020B-CUL |---|---|---|---| |---|---|---|---| |---|---|---|---| |<-- PIN 1 THIS CORNER LINE 1: 52B=AT25020B, U=MATERIAL SET/GRADE LINE 2: YM=DATE CODE, XX=TRACE CODE AT25020B-MAHL |---|---|---| |---|---|---| |---|---|---| |---|---|---| * | PIN 1 INDICATOR (DOT) LINE 1: 52B=AT25020B LINE 2: H=MATERIAL SET/GRADE, L=1 ...
Page 16
... AT25020B-MEHL |---|---|---| |---|---|---| |---|---|---| * | PIN 1 INDICATOR (DOT) LINE 1: 52B=AT25020B LINE 2: Y=DATE CODE, XX=TRACE CODE AT25040B-SSHL PIN 1 INDICATOR (DOT) | |---|---|---|---|---|---| * A T |---|---|---|---|---|---| 5 4 |---|---|---|---|---|---|---| |---|---|---|---|---|---|---| LINE 1: AT=ATMEL H=MATERIAL SET/GRADE YWW=DATE CODE LINE 2: 54B=AT25040B, L=1.8 to 5.5v, @=COUNTRY of ORIGIN LINE 3: ATMEL LOT NUMBER AT25040B-XHL PIN 1 INDICATOR (DOT) | |---|---|---|---|---|---| * A T |---|---|---|---|---|---| 5 4 |---|---|---|---|---|---|---| |---|---|---|---|---|---|---| ...
Page 17
AT25040B-CUL |---|---|---|---| |---|---|---|---| |---|---|---|---| |<-- PIN 1 THIS CORNER LINE 1: 54B=AT25040B, U=MATERIAL SET/GRADE LINE 2: YM=DATE CODE, XX=TRACE CODE AT25040B-MAHL |---|---|---| |---|---|---| |---|---|---| |---|---|---| ...
Page 18
... AT25010B-WWU11L Note: 1. Bulk delivery in tubes (SOIC and TSSOP 100/tube). 2. Tape and reel delivery (SOIC 4k/reel. TSSOP, UDFN, XDFN and VFBGA 5k/reel). 3. Contact Atmel Sales for Wafer sales. 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline Package (JEDEC SOIC) 8A2 8-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) 8MA2 8-lead, 2 ...
Page 19
... AT25020B Ordering Information Ordering Code (1) AT25020B-SSHL-B (NiPdAu Lead Finish) (2) AT25020B-SSHL-T (NiPdAu Lead Finish) (1) AT25020B-XHL-B (NiPdAu Lead Finish) (2) AT25020B-XHL-T (NiPdAu Lead Finish) (2) AT25020B-MAHL-T (NiPdAu Lead Finish) (2) AT25020B-MEHL-T (NiPdAu Lead Finish) (2) AT25020B-CUL-T (SnAgCu Ball Finish) (3) AT25020B-WWU11L Note: 1. Bulk delivery in tubes (SOIC and TSSOP 100/tube). ...
Page 20
... AT25040B-WWU11L Note: 1. Bulk delivery in tubes (SOIC and TSSOP 100/tube). 2. Tape and reel delivery (SOIC 4k/reel. TSSOP, UDFN, XDFN and VFBGA 5k/reel). 3. Contact Atmel Sales for Wafer sales. 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline Package (JEDEC SOIC) 8A2 8-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) 8MA2 8-lead, 2 ...
Page 21
... Packaging Information 8S1 – JEDEC SOIC GND SDA SCL e Notes: 1. These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. Package Drawing Contact: packagedrawings@atmel.com 8707B–SEEPR–3/ Top View Side View TITLE 8S1, 8-lead, (0.150” Wide Body), ...
Page 22
... Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimension D and determined at Datum Plane H. Package Drawing Contact: packagedrawings@atmel.com AT25010B/020B/040B End View D does ...
Page 23
... Dimensions b applies to metalized terminal and is measured between 0.15 mm and 0.30 mm from the terminal tip. If the terminal has the optional radius on the other end of the terminal, the dimension should not be measured in that radius area. Package Drawing Contact: packagedrawings@atmel.com 8707B–SEEPR–3/ Pin ...
Page 24
... XDFN 8 7 PIN # Top View Package Drawing Contact: packagedrawings@atmel.com AT25010B/020B/040B Side View TITLE 8ME1, 8-lead (1.80 x 2.20 mm Body) Extra Thin DFN (XDFN PIN # Bottom View COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX A – – 0.40 A1 0.00 – 0.05 1 ...
Page 25
... PIN 1 BALL PAD CORNER PIN 1 BALL PAD CORNER 1 (d1 (e1) Notes: 1. This drawing is for general information only. 2. Dimension ‘b’ is measured at maximum solder ball diameter. 3. Solder ball composition shall be 95.5Sn-4.0Ag-.5Cu Package Drawing Contact: packagedrawings@atmel.com 8707B–SEEPR–3/ Top View Bottom View ...
Page 26
Revision History Doc. Rev. Date 8707B 10/2010 8707B 3/2010 8707A 2/2010 AT25010B/020B/040B 26 Comments Remove Preliminary Replace 8Y6 with 8MA2 Initial document release 8707B–SEEPR–3/10 ...
Page 27
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...