MAX1320EVKIT Maxim Integrated, MAX1320EVKIT Datasheet
MAX1320EVKIT
Specifications of MAX1320EVKIT
Related parts for MAX1320EVKIT
MAX1320EVKIT Summary of contents
Page 1
... The MAX1320 EV system (MAX1320EVB16) consists of a MAX1320 evaluation kit (EV kit) and the Maxim 68HC16MOD-16WIDE microcontroller (µC) module. Order the EV kit (MAX1320EVKIT) separately if the user has a parallel bus controller or if the 68HC16MOD-16WIDE µC module has already been purchased. The MAX1320 EV kit can be used to evaluate the MAX1320 with an external system clock ...
Page 2
... TDK 847-803-6100 www.component.tdk.com Note: Indicate you are using the MAX1320 when contacting these component suppliers. Recommended Equipment • Maxim MAX1320EVB16 EV system (MAX1320EVKIT and 68HC16MOD-16WIDE µC module) • 3 power supplies higher (up to 20V) at 300mA for the 68HC16MOD-16WIDE 250mA for AVDD 3) ± ...
Page 3
MAX1320 Evaluation Kit/Evaluation System Detailed Description To start the software, double-click the MAX1320 EV kit icon that is created during installation. The Serial Form, shown in Figure 1, appears and the user must click Ok to upload the firmware to ...
Page 4
MAX1320 Evaluation Kit/Evaluation System Figure 1. MAX1320 EV Kit Serial Form Figure 2. MAX1320 Evaluation Software 4 _______________________________________________________________________________________ ...
Page 5
MAX1320 Evaluation Kit/Evaluation System Figure 3. MAX1320 EV Kit Sampling Tool Figure 4. MAX1320 EV Kit Graph Form _______________________________________________________________________________________ 5 ...
Page 6
MAX1320 Evaluation Kit/Evaluation System The negative supply must be applied on the HVAVEE pad. Connect the ground for these supplies to the AGND pad. If the IC has less than eight input channels (i.e., four channels or two channels), the ...
Page 7
MAX1320 Evaluation Kit/Evaluation System Table 5. Buffered Input Select SHUNT JUMPER POSITION Channel X (where X is determined by the jumper number minus 5) Short* input must appear on CHX-BUF pads and is buffered using the MAX4351. JU5–JU12 Channel X ...
Page 8
MAX1320 Evaluation Kit/Evaluation System Figure 5. 68HC16MOD-16WIDE Not-Found Error Message 8 _______________________________________________________________________________________ ...
Page 9
MAX1320 Evaluation Kit/Evaluation System 6 MSV C4 C23 JU1 2.2µF 0.1µF 18 REFMS C28 0.01µ JU13 19 REF C29 JU2 0.01µF 2.500V 20 REF+ C25 C5 C24 0.1µF 2.2µF 0.1µF 22 REF- C26 0.1µF 21 COM C6 ...
Page 10
MAX1320 Evaluation Kit/Evaluation System Figure 6. MAX1320 EV Kit Schematic (Sheet ______________________________________________________________________________________ ...
Page 11
MAX1320 Evaluation Kit/Evaluation System FB1 AVDD C1 2.2µF AGND DVDD VCC JU15 DVDD C20 2.2µF 0.1µF DGND J3 HEADER FEMALE J3-1 J3-2 J3-3 J3-4 J3-5 J3-6 VCC J3-7 J3-8 J3-9 J3-10 J3-11 J3-12 ...
Page 12
MAX1320 Evaluation Kit/Evaluation System Figure 7. MAX1320 EV Kit Component Placement Guide—Component Side 12 ______________________________________________________________________________________ ...
Page 13
MAX1320 Evaluation Kit/Evaluation System Figure 8. MAX1320 EV Kit PC Board Layout—Component Side ______________________________________________________________________________________ 13 ...
Page 14
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 14 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2005 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products, Inc ...