UMFT220XB-01

Manufacturer Part NumberUMFT220XB-01
DescriptionInterface Development Tools USB to SPI/FT1248 Breakout Brd FT220X
ManufacturerFTDI
TypeUSB to Serial
UMFT220XB-01 datasheet
 


Specifications of UMFT220XB-01

RohsyesProductDevelopment Modules
Tool Is For Evaluation OfFT220XQInterface TypeUSB
Operating Supply Voltage3.3 VDimensions45.5 mm x 14.95 mm x 5.2 mm
TradenameX-Chip  
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
9
Page 9
10
Page 10
11
12
13
14
15
16
Page 1/16

Download datasheet (483Kb)Embed
Next
Future Technology
Devices International
Ltd
Datasheet
UMFT201XB, UMFT220XB,
UMFT230XB Breakout
Modules
USB to I
Introduction
1
UMFT201XB, UMFT220XB, and UMFT230XB
breakout modules utilize FTDI’s FT201XQ,
FT220XQ, and FT230XQ chips, respectively,
to convert USB to serial or parallel interfaces.
. These modules support the following popular
interfaces:
-
UMFT201XB bridges from USB to I
-
UMFT220XB bridges from USB to a user
chosen, parallel bit interface, FTDI’s
FT1248/SPI. Note: 2 out of the 4 I/0 lines
are available for this module.
-
UMFT230XB bridges from USB to UART
IC.
Driver Support
2
Royalty-Free VIRTUAL COM PORT (VCP)
DRIVERS for:
Windows 7 32,64-bit
Windows Vista
Windows XP 32,64-bit
Windows XP Embedded
Windows CE.NET 4.2 , 5.0 and 6.0
MAC OS OS-X
Linux 3.0 and greater
Android
The drivers listed above are all available to download for free from www.ftdichip.com. Various 3rd Party Drivers
are also available for various other operating systems - visit
Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees
to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting
UMFT201XB, UMFT220XB and UMFT230XB Datasheet
Document Reference No.: FT_000506
2
C/UART/FT1248 breakout modules
Features
1.1
This hardware is a low cost breakout board form-factor
that converts USB2.0 Full-Speed to a serial interface
and connects the serial signals to a 2.54mm (0.1”) pitch
10pin female receptacle. The boards do not use a USB
connector, but instead the modules plug directly into
the USB host connector and the pads of the PCB makes
2
C IC.
electrical contact with the electrical contacts of the USB
connector.
All serial interfaces on these modules operate at +3.3V
voltage levels, however all I/Os are 5V tolerant.
Royalty-Free D2XX Direct Drivers (USB Drivers +
DLL S/W Interface):
Windows 7 32,64-bit
Windows Vista
Windows XP 32,64-bit
Windows XP Embedded
Windows CE.NET 4.2, 5.0 and 6.0
MAC OS OS-X
Linux 3.0 and greater
Android
www.ftdichip.com
from such use.
Version 1.0
Clearance No.: FTDI# 272
for details.

UMFT220XB-01 Summary of contents

  • Page 1

    ... USB to serial or parallel interfaces. . These modules support the following popular interfaces: - UMFT201XB bridges from USB UMFT220XB bridges from USB to a user chosen, parallel bit interface, FTDI’s FT1248/SPI. Note: 2 out of the 4 I/0 lines are available for this module. - UMFT230XB bridges from USB to UART IC ...

  • Page 2

    ... UMFT230XB Basic UART UMFT230XB-NC Basic UART UMFT230XB-WE Basic UART UMFT201XB, UMFT220XB and UMFT230XB Datasheet Document Reference No.: FT_000506 Features 2 USB with four control bus lines, 3.3V power out (with a 50mA current limit) and fused 5V. Standard option, connector fitted to CN2. 2 USB with four control bus lines, 3.3V power out (with a 50mA current limit) and fused 5V ...

  • Page 3

    ... Driver Support ................................................................................ 1 3 Ordering Information ..................................................................... 2 4 Signals and Configurations ............................................................. 4 4.1 UMFT-XB Module Pin Outs ............................................................................. 4 4.2 Signal Descriptions ....................................................................................... 4 4.3 UMFT201XB CN2 Signal Descriptions ............................................................ 5 4.4 UMFT220XB CN2 Signal Descriptions ............................................................ 5 4.5 UMFT230XB CN2 Signal Descriptions ............................................................ 6 4.6 CBUS Signal Options ..................................................................................... 6 4.7 Configuring the MTP ROM .............................................................................. 7 5 Module Dimensions ........................................................................ 8 6 UMFT-XB-WE Module Wire Connections .......................................... 9 6.1 UMFT201XB-WE Wire Connections ...

  • Page 4

    ... D- Signal Negative USB data signal 3 D+ Signal Positive USB data signal 4 GND PWR Module Ground Supply Table 4.2 CN1 PinOut Description UMFT201XB, UMFT220XB and UMFT230XB Datasheet Document Reference No.: FT_000506 FTUM220XBUMFT220XB IO0 VBUS GND RESET# SCK 3V3 SS# CB3 MISO IO1 Copyright © 2012 Future Technology Devices International Limited Version 1 ...

  • Page 5

    ... MTP ROM. Factory Default pin Function is PWREN#. See CBUS Signal Options, Table 4.6 Master In Serial Out. Used to provide status information to the FT1248 interface 9 MISO Output master. UMFT201XB, UMFT220XB and UMFT230XB Datasheet Document Reference No.: FT_000506 Copyright © 2012 Future Technology Devices International Limited Version 1.0 272 Clearance No.: FTDI# ...

  • Page 6

    ... PWREN# CBUS0, CBUS1, CBUS2, CBUS3 TXLED# CBUS0, CBUS1, CBUS2, CBUS3 RXLED# CBUS0, CBUS1, CBUS2, CBUS3 UMFT201XB, UMFT220XB and UMFT230XB Datasheet Document Reference No.: FT_000506 IO Pad is tri-stated Output a constant 1 Output a constant 0 Enable transmit data for RS485 (Only in UMFT230XB) Output is low after the device has been configured by USB, then high during USB suspend mode ...

  • Page 7

    ... USB host/hub when enumerated. For high-powered USB devices the current limit when enumerated is between 100mA and 500mA, for low-powered USB devices the current limit is 100mA. UMFT201XB, UMFT220XB and UMFT230XB Datasheet Document Reference No.: FT_000506 LED drive – pulses low when transmitting or receiving data via USB. ...

  • Page 8

    ... Measurements given in millimetres Figure 5.1 UMFT-XB Module Dimensions The UMFT201XB, UMFT220XB and UMFT230XB modules are mechanically identical. Figure 5.1 Uses UMFT230 to illustrate the mechanical details. UMFT201XB, UMFT220XB and UMFT230XB Datasheet Document Reference No.: FT_000506 45.5 Tolerance +/-0.1mm Copyright © 2012 Future Technology Devices International Limited Version 1 ...

  • Page 9

    ... GND 3 Figure 6.2 UMFT220XB-WE Wire Connections (numbers refer to pad numbers on the PCB) Figure 6.2 illustrates the –WE product as a cable. This is only for illustration purposes. The wire ended product consists of individual wires – not a cable UMFT201XB, UMFT220XB and UMFT230XB Datasheet Document Reference No.: FT_000506 Wire 6" ...

  • Page 10

    ... Figure 6.3 illustrates the –WE product as a cable. This is only for illustration purposes. The wire ended product consists of individual wires – not a cable Module Circuit Schematics 7 UMFT201XB Schematic 7.1 Figure 7.1 UMFT201XB Circuit Schematic UMFT201XB, UMFT220XB and UMFT230XB Datasheet Document Reference No.: FT_000506 Wire 6" Copyright © 2012 Future Technology Devices International Limited Version 1.0 272 Clearance No.: FTDI# ...

  • Page 11

    ... UMFT220XB Schematic 7.2 Figure 7.2 UMFT220XB Circuit Schematic UMFT230XB Schematic 7.3 Figure 7.3 UMFT230XB Circuit Schematic UMFT201XB, UMFT220XB and UMFT230XB Datasheet Document Reference No.: FT_000506 Copyright © 2012 Future Technology Devices International Limited Version 1.0 272 Clearance No.: FTDI# 11 ...

  • Page 12

    ... Device Type USB Version Remote Wake Up High Current I/Os Load VCP Driver UMFT201XB-01 CBUS0 UMFT201XB-01 CBUS1 UMFT201XB-01 CBUS2 UMFT201XB-01 CBUS3 UMFT220XB-01 CBUS3 UMFT230XB-01 CBUS0 UMFT201XB, UMFT220XB and UMFT230XB Datasheet Document Reference No.: FT_000506 Value Notes 0403h FTDI default VID (hex) 6015h FTDI default PID (hex) ...

  • Page 13

    ... FT_PROG can be downloaded from the www.ftdichip.com. Users who do not have their own USB vendor ID but who would like to use a unique Product ID in their design can apply to FTDI for a free block of unique PIDs. Contact FTDI Support UMFT201XB, UMFT220XB and UMFT230XB Datasheet Document Reference No.: FT_000506 Value Notes GPIO (support1@ftdichip ...

  • Page 14

    ... Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH, United Kingdom. Scotland Registered Company Number: SC136640 UMFT201XB, UMFT220XB and UMFT230XB Datasheet Document Reference No.: FT_000506 Branch Office – Hillsboro, Oregon, USA ...

  • Page 15

    ... Appendix A - List of Figures and Tables List of Figures Figure 6.1 UMFT201XB-WE Wire Connections (numbers refer to pad numbers on the PCB) ................ 9 Figure 6.2 UMFT220XB-WE Wire Connections (numbers refer to pad numbers on the PCB) ................ 9 Figure 6.3 UMFT230XB-WE Wire Connections (numbers refer to pad numbers on the PCB) .............. 10 Figure 7.1 UMFT201XB Circuit Schematic .................................................................................................. 10 Figure 7 ...

  • Page 16

    ... Document Title: Document Reference No.: Clearance No.: Product Page: Document Feedback: Version 1.0 Initial Datasheet Created Copyright © 2012 Future Technology Devices International Limited UMFT201XB, UMFT220XB and UMFT230XB Datasheet Document Reference No.: FT_000506 UMFT201XB, UMFT220XB and UMFT230XB FT_000506 FTDI# 272 http://www.ftdichip.com/FT-X.htm Send Feedback Version 1.0 272 Clearance No ...