V2-EVAL-UK

Manufacturer Part NumberV2-EVAL-UK
DescriptionBOARD, EVALUATION, UK PSU
ManufacturerFTDI
V2-EVAL-UK datasheet
 


Specifications of V2-EVAL-UK

Kit Contents1 X V2-Eval Base Board, 1x 5V/1A Mains Adapter PSU, 1x USB A/B Cable, 1x USB Gender ChangerSvhcNo SVHC (18-Jun-2010)
Kit FeaturesVNC2 Embedded USB Host / Slave Chip Accessible ViaSilicon ManufacturerFTDI
Silicon Family NameVinculum IIFeaturesEmbedded USB Host / Slave Chip, Two USB Type A Connectors
Rohs CompliantYesLead Free Status / RoHS StatusLead free / RoHS Compliant
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
9
Page 9
10
Page 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
Page 1/64

Download datasheet (3Mb)Embed
Next
Future Technology Devices International Ltd.
V2-EVAL
Vinculum II Evaluation Board
Datasheet
Document Reference No.: FT_000247
Version 2.0
Issue Date: 2010-07-29
Future Technology Devices International Ltd (FTDI)
Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow, G41 1HH, United Kingdom
Tel.: +44 (0) 141 429 2777
Fax: + 44 (0) 141 429 2758
E-Mail (Support):
support1@ftdichip.com
Web:
http://www.vinculum.com
Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced
in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are
supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology
Devices International Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your
statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in
which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary
information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by
the publication of this document. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park,
Glasgow, G41 1HH, United Kingdom. Scotland Registered Number: SC136640
Copyright © 2010 Future Technology Devices International Limited

V2-EVAL-UK Summary of contents

  • Page 1

    ... No freedom to use patents or other intellectual property rights is implied by the publication of this document. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow, G41 1HH, United Kingdom. Scotland Registered Number: SC136640 Copyright © 2010 Future Technology Devices International Limited V2-EVAL Datasheet Document Reference No.: FT_000247 Version 2.0 ...

  • Page 2

    ... USB2 interface CN2. ................................................................ 27 5.9 VNC1L Interface Mode Select / GPIO Jumpers JP1, JP2 .......... 28 5.10 User LEDs. LED3 – LED6. ......................................................... 29 Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 Table of Contents Clearance No.: FTDI#148 1 ...

  • Page 3

    ... VNC2 Daughterboard - 64-pin QFN Schematic ........................ 57 10 V2-EVAL Board Assembly Drawing ................................ 58 Contact Information ........................................................... 59 Appendix A – List of Figures and Tables .......................................... 60 List of Figures ................................................................................. 60 List of Tables ................................................................................... 62 Appendix B – Revision History ........................................... 63 Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 Clearance No.: FTDI#148 2 ...

  • Page 4

    ... Introduction The following document details the features and specifications of the V2-EVAL board. The V2-EVAL is a hardware platform designed to support easy evaluation of FTDI‟s Vinculum-II (VNC2) series of embedded USB host controller devices. The V2-Eval kit includes the following hardware items as standard 1 x V2-Eval base board. ...

  • Page 5

    ... V2-EVAL-EXT32 VNC2 daughterboard module with 32-pin QFN VNC2 device for use with V2-EVAL. V2-EVAL-EXT48 VNC2 daughterboard module with 48-pin QFN VNC2 device for use with V2-EVAL. V2-EVAL-EXT64 VNC2 daughterboard module with 64-pin QFN VNC2 device for use with V2-EVAL. Table 1.0 Part Numbers 1 ...

  • Page 6

    ... Master Out Slave In. SPI Serial Peripheral Interface. UART Universal Asynchronous Receiver/Transmitter. USB Universal Serial Bus. VNC2 Vinculum-II. Table 1.2 Acronyms and Abbreviations Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 Clearance No.: FTDI#148 5 ...

  • Page 7

    ... Board Description V2-Eval Board is intended for use as a hardware platform to enable easy evaluation of FTDI‟s Vinculum-II VNC2 series of embedded USB Host / Slave controllers. The V2-Eval Board includes all the necessary components required by a user to begin developing USB Host / Slave system applications based on the VNC2 device ...

  • Page 8

    ... V2-Eval Board Components and Interfaces This chapter describes the operational and connectivity information for the V2-Eval board major components and interfaces. Figure 3.1 V2-EVAL Board Layout Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 Clearance No ...

  • Page 9

    ... ECHO CH.C CH.A CH.D CH.B DEBUG 74CBT3257 MUX GPIO[0:7] Figure 3.2 V2-EVAL Board Block Diagram Copyright © 2010 Future Technology Devices International Limited V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 Host Host USB2 USB1 CN2 CN3 UART VNC2 Device PROG / RESET ...

  • Page 10

    ... Table 3.1 V2-Eval Board Components Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 Description FT4232H USB  Quad UART/FIFO device. 9356 Serial SPI EEPROM for FT4232H configuration data. 74CBT3257 4-bit, 1to2, FET Multiplexer/Demultiplexer. ...

  • Page 11

    ... Those pins are shared between different areas and connectors on the board. You can use only one device at time connected to those pins. Table 3.2 V2-Eval Board Interfaces Copyright © 2010 Future Technology Devices International Limited V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 Board designator Description CN1, CN2 VNC2 USB host ports 1&2. ...

  • Page 12

    ... Installing VNC2 Daughterboard Prior to first powering the board, users must ensure that the daughterboard module hosting the VNC2 chip is correctly installed on to the main V2-Eval board. The V2-Eval board has 4 socket connectors, J1- J4, onto which the VNC2 daughterboard module is installed. On the VNC2 daughterboard module, connector JN1 connects to corresponding socket J1, JN2 connects to socket J2, JN3 connects to socket J3 and JN4 connects the V2-Eval board ...

  • Page 13

    ... Connect the 5V DC/1A power supply included in V2-Eval Kit to the external input power adapter connector (CN12), connect USB A/B cable to USB B connector (CN13) on V2-Eval Board and to a free USB port on host PC. Switch SW1 to the ON position (towards board edge). LED2 – POWER should now be on ...

  • Page 14

    ... Figure 5.1 Power Select Jumper Configuration for USB Power V2-Eval Board can draw its power either from the external 5V/1A DC Power Supply or from the USB interface when connected to a USB host via the B type connector (CN13). To enable USB power supply feature, switch the jumper JP6 to USB position, pins 1&2 shorted (pin 1 has a rectangle shaped pad on the bottom side of the board) ...

  • Page 15

    ... GPIO BUS Connectors The V2-EVAL board features a set of 6 connectors providing access to GPIO capable pins on the VNC2 device. The GPIO pins are distributed across 6 connectors. outlined in subsequent sections. Further each connector has a 5V and 3.3V power and GND pins. 5.2.1 GPIO [0:7] Connector CN3 Figure 5 ...

  • Page 16

    ... USB bus. Table 5.2 GPIO[8:15] connector CN4 Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 VCN2 Pin No IO type 48-PIN 64-PIN ...

  • Page 17

    ... USB bus. Table 5.3 GPIO port connector CN5 Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 VCN2 Pin No IO type 48-PIN 64-PIN ...

  • Page 18

    ... USB bus. Table 5.4 GPIO port connector CN6 Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 VCN2 Pin No IO type 48-PIN ...

  • Page 19

    ... USB power bus. Table 5.5 GPIO port connector CN7 Copyright © 2010 Future Technology Devices International Limited V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 VCN2 Pin No 48-PIN 64-PIN 29 ...

  • Page 20

    ... USB bus. Table 5.6 GPIO port connector CN8 Copyright © 2010 Future Technology Devices International Limited V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 VCN2 Pin No 48-PIN 64-PIN - ...

  • Page 21

    ... Care should be taken to ensure that pins are not driven from other headers on the board. Table 5.7 SPI Port Connector CN9 Copyright © 2010 Future Technology Devices International Limited V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 VCN2 Pin No IO type 64-PIN - ...

  • Page 22

    ... USB power bus. Table 5.8 UART Interface Connector CN10 Copyright © 2010 Future Technology Devices International Limited V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 VCN2 Pin No IO type 48-PIN 64-PIN ...

  • Page 23

    ... USB bus. Table 5.9 FIFO Interface Connector CN11 Copyright © 2010 Future Technology Devices International Limited V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 VCN2 Pin No IO type 48-PIN 64-PIN ...

  • Page 24

    ... Only the first column is connected to VNC2 IO ports, power and ground planes. All the other holes are not connected to anything on the board. Signal pins are shared between other IO connectors on the board. For more information refer to the V2- Eval Board schematics. ...

  • Page 25

    ... IOBUS33 30 (34) 40 IOBUS34 31 (34) 41 IOBUS35 32 Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 VCN2 Pin No IO type 48-PIN 64-PIN - - - Ground pin 5V power rail Can be used to power external devices 3.3V power rail. ...

  • Page 26

    ... The following pins are only accessible when the onboard multiplexer select input is high. See section 6.4 for details. Table 5.10 Prototyping Area Pinout Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2 IOBUS port Data Bit 36. - ...

  • Page 27

    ... USB power bus. Table 5.11 USB1 Host/Slave Connector CN1 Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 VCN2 pin number IO type 32- 48- ...

  • Page 28

    ... USB power bus. Table 5.12 USB2 Host / Slave connector CN2 Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 VCN2 pin number IO Description 32- 48- ...

  • Page 29

    ... Pull-down Pull-up Pull-down Pull-down Table 5.14 Monitor Interface Select – VNC1L Firmware Backwards Compatiblity Copyright © 2010 Future Technology Devices International Limited V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 VNC2 Signal Name Comments 64-PIN 29 / IOBUS17 INT_SEL0. Signal also connected to LED5 - INT_SEL1. ...

  • Page 30

    ... VNC1L migrated firmwares, LED5 is not available on 48-pin package as the I/O signal is used for interface selection purposes by the firmware. Table 5.15 User LED connections Copyright © 2010 Future Technology Devices International Limited V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 VCN2 pin number 32-PIN 48-PIN 12 ...

  • Page 31

    ... Table 5.17 User Switches Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 LED affected LED3 LED4 LED5 LED6 ...

  • Page 32

    ... Warning! When using USB1 and USB2 ports as a USB slave ports, remove the shunts from jumpers JP4 and JP5. Failure could cause damage to the USB host or to the V2-EVAL board. Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2 ...

  • Page 33

    ... SUM mode immediately. The remote wakeup feature is only available when using the UART interface on the VNC2. The feature can be enabled when a jumper is present on jumper JP3. Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 Clearance No.: FTDI#148 32 ...

  • Page 34

    ... A „RESET‟ push button switch is provided on switch SW2, to enable manual resetting of the VNC2 device. 5.16 ‘PROG’ LED Figure 5.21 ‘PROG’ LED LED1 (red) is provided to indicate when VNC2 device is in Flash programming mode. Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 Clearance No.: FTDI#148 33 ...

  • Page 35

    ... V_DTR# 16 Notes: (43) The signal names relate to the labels used on pages 1 & the V2-EVAL base board schematic. Unless otherwise stated, the function of the IO signals is be set by the user application running on the VNC2. Table 5.18 Connector J1 Pinout Copyright © 2010 Future Technology Devices International Limited V2-EVAL Vinculum II Evaluation Board Datasheet Version 2 ...

  • Page 36

    ... GND 16 Notes: (44) The signal names relate to the labels used on pages 1 & the V2-EVAL base board schematic. Unless otherwise stated, the function of the IO signals is set by the user application running on the VNC2. Table 5.19 Connector J2 Pinout Copyright © 2010 Future Technology Devices International Limited V2-EVAL Vinculum II Evaluation Board Datasheet Version 2 ...

  • Page 37

    ... GND 16 Notes: (45) The signal names relate to the labels used on pages 1 & the V2-EVAL base board schematic. Unless otherwise stated, the function of the IO signals is set by the user application running on the VNC2. Table 5.20 Connector J3 Pinout Copyright © 2010 Future Technology Devices International Limited V2-EVAL Vinculum II Evaluation Board Datasheet Version 2 ...

  • Page 38

    ... GND 16 Notes: (46) The signal names relate to the labels used on pages 1 & the V2-EVAL base board schematic. Unless otherwise stated, the function of the IO signals is set by the user application running on the VNC2. Table 5.21 Connector J4 Pinout Copyright © 2010 Future Technology Devices International Limited V2-EVAL Vinculum II Evaluation Board Datasheet Version 2 ...

  • Page 39

    ... FT4232H Configuration The V2-EVAL board features a FT4232H, a high speed USB to quad channel UART / serial converter device. The device is primarily featured to provide a connection from the board host via the onboard USB type B connector. Each of the four channels on the FT4232H device are used to provide a separate functions on the V2-EVAL board ...

  • Page 40

    ... FT4232H device external UART device, which is connected to the V2-EVAL board via the various board I/O header pins. The multiplexer select pin is controlled by pin DDBUS0 on the FT4232H, where a logic „0‟ on the select pin will force the FT4232H device to drive the UART interface on the VNC2, while a logic „ ...

  • Page 41

    ... Both pins are passed to the onboard multiplexer. multiplexer select input will allow the VNC2 PROG# and RESET# pins to be controlled by the FT4232H. Table 6.1, summarises the V2-EVAL board settings based on the value of the multiplexer select pin. Multiplexer Select Pin Status (Set by FT4232H DDBUS0) ...

  • Page 42

    ... Connecting Host Connect a USB A/B cable to USB slave connector CN13 on the V2-EVAL board. Connect the other end to PC computer and power-up the board. The PC should detect that new hardware has been plugged into the PC and will launch the Hardware Wizard for installing the drivers. The driver installation procedure is outlined in the following section ...

  • Page 43

    ... Windows Logo testing. If the warning is received, click on „Continue Anyway‟ to continue with the installation. Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 Clearance No.: FTDI#148 42 ...

  • Page 44

    ... Serial Bus Controllers”. Further under the “Ports” section four “USB Serial Ports” should be listed, as per Figure 7.6. Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 Clearance No.: FTDI#148 43 ...

  • Page 45

    ... V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 Figure 7.6: Device Manager Screen Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 Clearance No.: FTDI#148 Each port of FT4232H is recognised as a USB Serial COM Port with a relevant port number. USB Serial Converter ...

  • Page 46

    ... The following section details instructions on how to install and use the V2-EVAL software terminal utility for the V2-EVAL board. 8.1 V2-EVAL Terminal Installation A simple terminal application has been designed for use with the VNC2 V2-EVAL board. The application can be downloaded as part of the Vinculum II utilities available from: http://www.ftdichip.com/Firmware/VNC2tools.htm Note: The V2-EVAL terminal software is only supported under WindowXP, Vista and Windows 7 Operating Systems ...

  • Page 47

    ... Enables full UART TX and RX operation through the V2-EVAL terminal utility. Under the UART mode the select line of the V2-EVAL board multiplexer U4 is set to „0‟ forcing the FT4232H channel A to connect to UART interface on VNC2, as per the conditions outlined in Table 6.1. „ ...

  • Page 48

    ... The following section outlines the steps to connect an external UART device to the VNC2 interface and enabling the „Spy‟ mode. 1. The first step is to connect an external UART device to the VNC2 UART interface on the V2-EVAL board. An external device can be connected to the board via I/O connectors CN3 – CN11 or via the IOBUS connections in prototyping area P1 ...

  • Page 49

    ... Next open a connection to the „Spy‟ channel on the V2-EVAL board. From the Vinculum logo pull down menu, select „Connect to UART->VII Eval Board C‟ to open the UART connection to channel C on the FT4232H. Figure 8.5: Connect to ‘Spy’ channel on V2-EVAL board The V2-EVAL board and software is now ready to display „Spy‟ data being sent to the VNC2 device from an external device. An example displaying „ ...

  • Page 50

    ... Board Schematics. Schematics for the V2-EVAL board and VNC2 daughterboards are found in the following section. Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 Clearance No.: FTDI#148 49 ...

  • Page 51

    ... V2-EVAL Board Schematics Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 Clearance No.: FTDI#148 50 ...

  • Page 52

    ... V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 Clearance No.: FTDI#148 51 ...

  • Page 53

    ... V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 Clearance No.: FTDI#148 52 ...

  • Page 54

    ... V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 Clearance No.: FTDI#148 53 ...

  • Page 55

    ... V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 Clearance No.: FTDI#148 54 ...

  • Page 56

    ... VNC2 Daughterboard - 32-pin QFN Schematic Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 Clearance No.: FTDI#148 55 ...

  • Page 57

    ... VNC2 Daughterboard - 48-pin QFN Schematic Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 Clearance No.: FTDI#148 56 ...

  • Page 58

    ... VNC2 Daughterboard - 64-pin QFN Schematic Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 Clearance No.: FTDI#148 57 ...

  • Page 59

    ... V2-EVAL Board Assembly Drawing Dimensions in mm.Tolerance is ±0.1mm Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 Clearance No.: FTDI#148 58 ...

  • Page 60

    ... Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 Clearance No.: FTDI#148 59 ...

  • Page 61

    ... Appendix A – List of Figures and Tables Figure 1.1 - V2-EVAL Motherboard(left) with Daughterboard Module(right) .......................................... 3 Figure 3.1 V2-EVAL Board Layout .............................................................................................. 7 Figure 3.2 V2-EVAL Board Block Diagram ............................................................................... 8 Figure 4.1 V2-EVAL Board with VNC2 Daughterboard Installed .................................................... 11 Figure 4.2 Power connector with Jumper JP6 ...................................................................... 12 Figure 5.1 Power Select Jumper Configuration for USB Power ...

  • Page 62

    ... Figure 8.3: Example IOMUX configuration code ....................................................................... 47 Figure 8.4: V2-EVAL Terminal connection with ‘Spy’ connection enabled ................................ 47 Figure 8.5: Connect to ‘Spy’ channel on V2-EVAL board ........................................................... 48 Figure 8.6: ‘Spy’ mode operation ............................................................................................. 48 Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2 ...

  • Page 63

    ... Connector J1 Pinout ............................................................................................ 34 Table 5.19 Connector J2 Pinout ............................................................................................ 35 Table 5.20 Connector J3 Pinout ............................................................................................ 36 Table 5.21 Connector J4 Pinout ............................................................................................ 37 Table 6.1: Multiplexer Configuration Settings ...................................................................... 40 Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 List of Tables Clearance No.: FTDI#148 62 ...

  • Page 64

    ... Appendix B – Revision History Rev 1.0 First Release Rev 2.0 Second Release Copyright © 2010 Future Technology Devices International Limited Document Reference No.: FT_000247 V2-EVAL Vinculum II Evaluation Board Datasheet Version 2.0 Clearance No.: FTDI#148 15th April 2010 th 27 July 2010 63 ...