CAT24C164WI-G ON Semiconductor, CAT24C164WI-G Datasheet
CAT24C164WI-G
Specifications of CAT24C164WI-G
Available stocks
Related parts for CAT24C164WI-G
CAT24C164WI-G Summary of contents
Page 1
... Data is written by providing a starting address, then loading contiguous bytes into a Page Write Buffer, and then writing all data to non−volatile memory in one internal write cycle. Data is read by providing a starting address and then shifting out data serially while automatically incrementing the internal address count. ...
Page 2
Table 1. ABSOLUTE MAXIMUM RATINGS Parameters Storage Temperature Voltage on Any Pin with Respect to Ground (Note 1) Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is ...
Page 3
Table 5. A.C. CHARACTERISTICS Symbol F Clock Frequency SCL t START Condition Hold Time HD:STA t Low Period of SCL Clock LOW t High Period of SCL Clock HIGH t START Condition Setup Time SU:STA t Data In Hold Time ...
Page 4
Power-On Reset (POR) CAT24C164 incorporates Power−On Reset (POR) circuitry which protects the internal logic against powering up in the wrong state. A CAT24C164 device will power up into Standby mode after V exceeds the POR trigger level and will power ...
Page 5
SCL SDA START CONDITION BUS RELEASE DELAY (TRANSMITTER) SCL FROM 1 MASTER DATA OUTPUT FROM TRANSMITTER DATA OUTPUT FROM RECEIVER START LOW SCL t SU:STA t HD:STA SDA IN SDA OUT Figure 2. START/STOP Conditions 1 A2 ...
Page 6
... CAT24C164. After receiving another acknowledge from the Slave, the Master transmits the data byte to be written into the addressed memory location. The CAT24C164 device will acknowledge the data byte and the Master generates the STOP condition, at which time the device begins its internal Write cycle to nonvolatile memory (Figure 6) ...
Page 7
S BUS ACTIVITY SLAVE R ADDRESS MASTER T S SLAVE SCL SDA 8th Bit Byte n BUS S ACTIVITY SLAVE ADDRESS R ADDRESS MASTER SLAVE ≤ 15 ...
Page 8
... CAT24C164 will continue transmitting data residing at subsequent locations until the Master responds with a NoACK, followed by a STOP (Figure 12). In contrast to Page Write, during Sequential Read the address count will automatically increment to and then wrap−around at end of memory (rather than end of page SLAVE ...
Page 9
PIN # 1 IDENTIFICATION D TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. (2) Complies with JEDEC MS-001. PACKAGE DIMENSIONS PDIP−8, 300 mils CASE 646AA−01 ISSUE A SYMBOL ...
Page 10
PIN # 1 IDENTIFICATION TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MS-012. PACKAGE DIMENSIONS SOIC 8, 150 mils CASE 751BD−01 ISSUE O SYMBOL ...
Page 11
E1 e TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-153. PACKAGE DIMENSIONS TSSOP8, 4.4x3 CASE 948AL−01 ISSUE O SYMBOL MIN A A1 0.05 A2 ...
Page 12
D E PIN#1 INDEX AREA TOP VIEW SYMBOL MIN NOM A 0.70 0.75 A1 0.00 0.02 A2 0.45 0.55 A3 0.20 REF b 0.20 0.25 D 1.90 2.00 D2 1.30 1.40 E 2.90 3.00 E2 1.20 1.30 e 0.50 TYP ...
Page 13
Package Marking 8−Lead PDIP 24C164LI FYYWW Temperature Range YY = Production Year WW = Production Week G = Product Revision F = Lead Finish = 4 = NiPdAu 8−Lead TSSOP YMGF 24164I Y = Production Year M ...
Page 14
... Y: TSSOP VP2: TDFN ORDERING INFORMATION Orderable Part Numbers CAT24C164LI−G CAT24C164WI−GT3 CAT24C164YI−GT3 CAT24C164VP2IGT3 (Note 15) 11. All packages are RoHS-compliant (Lead-free, Halogen-free). 12. The standard lead finish is NiPdAu. 13. The device used in the above example is a CAT24C164YI−GT3 (TSSOP, Industrial Temperature, NiPdAu, Tape & Reel, 3,000/Reel). ...