IC OFFLINE SWIT UVLO HV TO220

TOP242YN

Manufacturer Part NumberTOP242YN
DescriptionIC OFFLINE SWIT UVLO HV TO220
ManufacturerPower Integrations
SeriesTOPSwitch®-GX
TypeOff Line Switcher
TOP242YN datasheet
 


Specifications of TOP242YN

Output IsolationIsolatedFrequency Range66 ~ 132kHz
Voltage - Output700VPower (watts)22W
Operating Temperature-40°C ~ 150°CPackage / CaseTO-220-7 (Formed Leads), 5 Leads
Output Voltage12 VInput / Supply Voltage (max)265 VAC
Input / Supply Voltage (min)85 VACDuty Cycle (max)83 %
Switching Frequency132 KHzSupply Current1.6 mA
Operating Temperature Range- 40 C to + 150 CMounting StyleThrough Hole
Lead Free Status / RoHS StatusLead free / RoHS CompliantOther names596-1067-5
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
9
Page 9
10
Page 10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
Page 6/52

Download datasheet (3Mb)Embed
PrevNext
TOP242-250
CONTROL (C) Pin Operation
The CONTROL pin is a low impedance node that is capable
of receiving a combined supply and feedback current. During
normal operation, a shunt regulator is used to separate the
feedback signal from the supply current. CONTROL pin voltage
V
is the supply voltage for the control circuitry including the
C
MOSFET gate driver. An external bypass capacitor closely
connected between the CONTROL and SOURCE pins is required
to supply the instantaneous gate drive current. The total amount
of capacitance connected to this pin also sets the auto-restart
timing as well as control loop compensation.
When rectified DC high voltage is applied to the DRAIN
pin during start-up, the MOSFET is initially off, and the
CONTROL pin capacitor is charged through a switched high
voltage current source connected internally between the DRAIN
and CONTROL pins. When the CONTROL pin voltage V
reaches approximately 5.8 V, the control circuitry is activated
and the soft-start begins. The soft-start circuit gradually
increases the duty cycle of the MOSFET from zero to the
maximum value over approximately 10 ms. If no external
feedback/supply current is fed into the CONTROL pin by the
end of the soft-start, the high voltage current source is turned
off and the CONTROL pin will start discharging in response
to the supply current drawn by the control circuitry. If the
power supply is designed properly, and no fault condition
such as open loop or shorted output exists, the feedback loop
will close, providing external CONTROL pin current, before
the CONTROL pin voltage has had a chance to discharge to
the lower threshold voltage of approximately 4.8 V (internal
supply under-voltage lockout threshold). When the externally
fed current charges the CONTROL pin to the shunt regulator
V
UV
V
LINE
0 V
S0
S7
S1
V
C
0 V
V
DRAIN
0 V
V
OUT
0 V
1
2
Note: S0 through S7 are the output states of the auto-restart counter
Figure 8. Typical Waveforms for (1) Power Up (2) Normal Operation (3) Auto-Restart (4) Power Down.
6
O
11/05
voltage of 5.8 V, current in excess of the consumption of the
chip is shunted to SOURCE through resistor R
Figure 2. This current flowing through R
of the power MOSFET to provide closed loop regulation. The
shunt regulator has a finite low output impedance Z
the gain of the error amplifier when used in a primary feedback
configuration. The dynamic impedance Z
pin together with the external CONTROL pin capacitance sets
the dominant pole for the control loop.
When a fault condition such as an open loop or shorted output
prevents the flow of an external current into the CONTROL
pin, the capacitor on the CONTROL pin discharges towards
4.8 V. At 4.8 V, auto-restart is activated which turns the output
MOSFET off and puts the control circuitry in a low current
standby mode. The high-voltage current source turns on and
charges the external capacitance again. A hysteretic internal
C
supply under-voltage comparator keeps V
of typically 4.8 V to 5.8 V by turning the high-voltage current
source on and off as shown in Figure 8. The auto-restart
circuit has a divide-by-eight counter which prevents the output
MOSFET from turning on again until eight discharge/charge
cycles have elapsed. This is accomplished by enabling the
output MOSFET only when the divide-by-eight counter reaches
full count (S7). The counter effectively limits TOPSwitch-GX
power dissipation by reducing the auto-restart duty cycle
to typically 4%. Auto-restart mode continues until output
voltage regulation is again achieved through closure of the
feedback loop.
Oscillator and Switching Frequency
The internal oscillator linearly charges and discharges an
S2
S6
S7
S0
S1
S2
S6
S7
3
as shown in
E
controls the duty cycle
E
of the CONTROL
C
within a window
C
S0
S1
S2
S6
S7
S7
4.8 V
2
4
that sets
C
5.8 V
PI-2545-082299