MAX1758EAI+ Maxim Integrated Products, MAX1758EAI+ Datasheet - Page 13

• Manufacturer Part Number: MAX1758EAI+
• Description: IC BATT CHRG 4-LI+ 28V SW 28SSOP
• Manufacturer: Maxim Integrated Products

Specifications of MAX1758EAI+

• Function: Charge Management
• Battery Type: Lithium-Ion (Li-Ion)
• Voltage - Supply: 6 V ~ 28 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 28-SSOP
• Output Voltage: 5.4 V
• Operating Supply Voltage: 6 V to 28 V
• Supply Current: 5 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Charge Safety Timers: Yes
• Mounting Style: SMD/SMT
• Temperature Monitoring: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

When the current-sense resistor is chosen, note that the
voltage drop across this resistor adds to the power
loss, reducing efficiency. Reducing the voltage across
the current-sense resistor may degrade input current
limit accuracy due to the input offset of the input cur-
rent-sense amplifier.
The input current error amplifier (GMS) is compensated
at CCS. A 0.1µF capacitor at CCS provides suitable
performance for most applications.
The PWM controller drives the internal high-side MOS-
FET to control charging current or voltage. The input to
the PWM controller is the lowest of CCI, CCV, or CCS.
Figure 4. State Diagram
Li+ Battery Charger with Internal 28V Switch
______________________________________________________________________________________
V
BATT
NOT OK
TEMP
THRESHOLD
< UNDERVOLTAGE
NOT OK
TEMP
TEMP
QUAL
V
FULLCHG = HIGH
FASTCHG = LOW
DCIN
FAULT = HIGH
PREQUAL
V
DCIN
> V
TEMP
TEMP
OK
BATT
OK
ONCE PER
PWM Controller
< BATT
SECOND
TEMP
OK
ONCE PER
SECOND
FASTCHG = HIGH
FULLCHG = HIGH
FAULT = HIGH
V
PREQUAL
NOT OK
TIMEOUT
BATT
TEMP
RESET
TEMP
OK
> 2.5V
FULLCHG = HIGH
FULL CHARGE
FASTCHG = HIGH
FULLCHG = LOW
FASTCHG = HIGH
FULLCHG = HIGH
FAST CHARGE
FASTCHG = LOW
FAULT = HIGH
FAULT = HIGH
FAULT = HIGH
TOP-OFF
Stand-Alone, Switch-Mode
SHDN HIGH
REGULATION VOLTAGE (V
FASTCHG = HIGH
FULLCHG = HIGH
I
V
SHUTDOWN
FAULT = HIGH
CHARGE
BATT
FULL-CHARGE
FASTCHG = HIGH
FULLCHG = HIGH
FAST-CHARGE
FAULT = LOW
TIMEOUT
TIMEOUT
FAULT
= BATTERY
An internal clamp limits the noncontrolling signals to
within 200mV of the controlling signal to prevent delay
when switching between regulation loops.
The current mode PWM controller measures the induc-
tor current to regulate the output voltage or current,
simplifying stabilization of the regulation loops.
Separate compensation of the regulation circuits allows
each to be optimally stabilized. Internal slope compen-
sation is included, ensuring stable operation over a
wide range of duty cycles.
The controller drives an internal N-channel MOSFET
switch to step the input voltage down to the battery
voltage. The high-side MOSFET gate is driven to a volt-
age higher than the input source voltage by a bootstrap
< I
TIMEOUT
TOP-OFF
MIN
OR
V
BATT
ENTERED FROM ALL STATES
< 0.95 × V
BATTR
WHEN SHDN IS LOW.
SHUTDOWN IS
FASTCHG = HIGH
FULLCHG = HIGH
)
FAULT = HIGH
BATTR
DONE
V
BATT
< 0.95 × V
BATTR
13