LTC1642IGN Linear Technology, LTC1642IGN Datasheet
LTC1642IGN
Specifications of LTC1642IGN
Related parts for LTC1642IGN
LTC1642IGN Summary of contents
Page 1
... The ON pin cycles the board power. The LTC1642 is available in the 16-pin SSOP package. , LTC and LT are registered trademarks of Linear Technology Corporation. Hot Swap is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. ...
Page 2
... FAULT GND T ORDER PART NUMBER LTC1642CGN LTC1642IGN Order Options Tape and Reel: Add #TR Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF Lead Free Part Marking: Consult LTC Marketing for parts specified with wider operating temperature ranges. CONDITIONS Rising ...
Page 3
DC ELECTRICAL CHARACTERISTICS The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are unless otherwise specified. CC SYMBOL PARAMETER I CRWBR Pin Current CR V Circuit Breaker Trip Voltage ...
Page 4
LTC1642 W U TYPICAL PERFOR A CE CHARACTERISTICS I Pull-Up Current vs V GATE GATE T = 25° (V) CC 1642 G23 CRWBR ...
Page 5
W U TYPICAL PERFOR A CE CHARACTERISTICS FAULT and RESET Pull-Up Current ( 160 140 120 T = –55°C A 100 T = 25° 125° ...
Page 6
LTC1642 CTIO S CRWBR (Pin 1): Overvoltage Crowbar Circuit Timer and Trigger. This pin controls an external overvoltage crowbar circuit. A capacitor from the pin to ground sets a 9ms/µF delay after an overvoltage occurs ...
Page 7
CTIO S OV (Pin 9): Overvoltage Input. When the voltage on OV exceeds its trip point the GATE pin is pulled low immedi- ately and the CRWBR timer starts remains above its trip ...
Page 8
LTC1642 W BLOCK DIAGRA 23mV TO 53mV – – + SENSE 15 – 21V + 1.22V + OV 9 21V – 1.22V + ON 4 21V – 1.22V + V CC – ...
Page 9
U U APPLICATIO S I FOR ATIO Hot Circuit Insertion When a circuit board is inserted into a live backplane its supply bypass capacitors can draw large currents from the backplane power bus as they charge. These currents can permanently ...
Page 10
LTC1642 U U APPLICATIO S I FOR ATIO an internal servo loop adjusts the GATE pin voltage such that Q1 acts as a constant current source. The voltage limit across R2 increases as the output charges; this foldback in the ...
Page 11
U U APPLICATIO S I FOR ATIO Automatic Restart After the Circuit Breaker Opens The LTC1642 will automatically attempt to restart itself after the circuit breaker opens if the FAULT output is tied to the ON pin. The circuit is ...
Page 12
LTC1642 U U APPLICATIO S I FOR ATIO Overvoltage Protection The LTC1642 can protect a load from overvoltages by turning off the pass transistor if the supply voltage ex- ceeds an adjustable limit, and by triggering a crowbar SCR if ...
Page 13
U U APPLICATIO S I FOR ATIO Automatic Restart If there is an overvoltage, and the resistor divider feeding OV is connected to the output of the N-Channel pass transistor, the LTC1642 will automatically restart even if FAULT is not ...
Page 14
LTC1642 U U APPLICATIO S I FOR ATIO The undervoltage monitor behaves differently above its threshold when the GATE begins ramping: RESET goes high as soon as the GATE ramp begins. RESET goes low immediately if V ...
Page 15
... COMPOUT pins may be left floating. RESISTOR, R2 Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights. W ...
Page 16
... Single Supply from 2.5V to 16.5V, MSOP Package – 48V Supplies, Active Current Limit 3.3V, 5V, ±12V Supplies for PCI Bus, Active Current Limit LT/LT 0805 REV B • PRINTED IN USA © LINEAR TECHNOLOGY CORPORATION 1999 .045 ±.005 .150 – .165 .0250 BSC ...