IR11662SPBF International Rectifier, IR11662SPBF Datasheet - Page 11

• Manufacturer Part Number: IR11662SPBF
• Description: IC CNTROL SMART RECTIFIER 8-SOIC
• Manufacturer: International Rectifier
• Series: Advanced Smart Rectifier™r

Specifications of IR11662SPBF

• Configuration: High-Side
• Input Type: Non-Inverting
• Delay Time: 60ns
• Current - Peak: 1A
• Number Of Configurations: 1
• Number Of Outputs: 1
• Voltage - Supply: 11.4 V ~ 18 V
• Operating Temperature: -25°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: *
• Device Type: MOSFET
• Module Configuration: Half Bridge
• Peak Output Current: 4A
• Input Delay: 60ns
• Output Delay: 50ns
• Supply Voltage Range: 11.4V To 18V
• Driver Case Style: SOIC
• No. Of Pins: 8
• Rohs Compliant: Yes
• Part Status: Active and Preferred
• Package: 8-Pin SOIC(NB)
• Circuit: Switching Regulator Controller
• Topology: Flyback / Resonant Half-Bridge
• Current Mode: Discontinuous / Critical
• Vcc (min): 11.4
• Vcc (max): 18
• Vout (max): 200
• Iout (a): +1 / -4
• Switch Freq (khz): up to 500kHz
• Vgate Clamp (v): 10.7
• Programmability: MOT / OVT
• Enable Pin: Yes
• Isleep (ua): 200
• Automatic Mot Protection: Yes
• Pbf: PbF Option Available
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• High Side Voltage - Max (bootstrap): -

IR11662S
Detailed Pin Description
VCC: Power Supply
This is the supply voltage pin of the IC and it is monitored by the under voltage lockout circuit. It is possible to
turn off the IC by pulling this pin below the minimum turn off threshold voltage, without damage to the IC.
To prevent noise problems, a bypass ceramic capacitor connected to Vcc and COM should be placed as
close as possible to the IR11662. This pin is internally clamped.
OVT: Offset Voltage Trimming
The OVT pin will program the amount of input offset voltage for the turn-off threshold V
.
TH1
The pin can be optionally tied to ground, to VCC or left floating, to select 3 ranges of input offset trimming.
This programming feature allows for accommodating different R
MOSFETs.
Dson
MOT: Minimum On Time
The MOT programming pin controls the amount of minimum on time. Once V
is crossed for the first time,
TH2
the gate signal will become active and turn on the power FET. Spurious ringings and oscillations can trigger
the input comparator off. The MOT blanks the input comparator keeping the FET on for a minimum time.
The MOT is programmed between 200ns and 3us (typ.) by using a resistor referenced to COM.
EN: Enable
This pin is used to activate the IC “sleep” mode by pulling the voltage level below 1.6V (typ). In sleep mode
the IC will consume a minimum amount of current. All switching functions will be disabled and the gate will be
inactive.
VD: Drain Voltage Sense
VD is the voltage sense pin for the power MOSFET Drain. This is a high voltage pin and particular care must
be taken in properly routing the connection to the power MOSFET drain.
Additional filtering and or current limiting on this pin are not recommended as it would limit switching
performance of the IC.
VS: Source Voltage Sense
VS is the differential sense pin for the power MOSFET Source. This pin must not be connected directly to the
power ground pin (7) but must be used to create a Kelvin contact as close as possible to the power MOSFET
source pin.
GND: Ground
This is ground potential pin of the integrated control circuit.
The internal devices and gate driver are
referenced to this point.
VGATE: Gate Drive Output
This is the gate drive output of the IC. Drive voltage is internally limited and provides 1A peak source and 4A
peak sink capability. Although this pin can be directly connected to the power MOSFET gate, the use of
minimal gate resistor is recommended, especially when putting multiple FETs in parallel.
Care must be taken in order to keep the gate loop as short and as small as possible in order to achieve
optimal switching performance.
www.irf.com
© 2010 International Rectifier
11