MIC4452BM Micrel Inc, MIC4452BM Datasheet - Page 8

• Manufacturer Part Number: MIC4452BM
• Description: IC DRIVER MOSF 12A LO SIDE 8SOIC
• Manufacturer: Micrel Inc

Specifications of MIC4452BM

• Rise Time: 20ns
• Mounting Type: Surface Mount
• Configuration: Low-Side
• Input Type: Non-Inverting
• Delay Time: 15ns
• Current - Peak: 12A
• Number Of Configurations: 1
• Number Of Outputs: 1
• Voltage - Supply: 4.5 V ~ 18 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• Device Type: MOSFET
• Driver Case Style: SOIC
• No. Of Pins: 8
• Peak Output High Current, Ioh: 12A
• Supply Voltage Min: 4.5V
• Peak Reflow Compatible (260 C): No
• Number Of Drivers: 1
• Driver Configuration: Non-Inverting
• Driver Type: Low Side
• Input Logic Level: CMOS/TTL
• Fall Time: 50ns
• Propagation Delay Time: 60ns
• Operating Supply Voltage (max): 18V
• Peak Output Current: 12mA
• Power Dissipation: 1.04W
• Output Resistance: 0.8Ohm
• Operating Supply Voltage (min): 4.5V
• Turn Off Delay Time: 80fs
• Turn On Delay Time (max): 40ps
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 8
• Package Type: SOIC
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• High Side Voltage - Max (bootstrap): -
• Lead Free Status / RoHS Status: Not Compliant, Contains lead / RoHS non-compliant

Applications Information
Supply Bypassing
Charging and discharging large capacitive loads quickly
requires large currents. For example, changing a
10,000pF load to 18V in 50ns requires 3.6A.
The MIC4451/4452 has double bonding on the supply
pins, the ground pins and output pins. This reduces
parasitic lead inductance. Low inductance enables large
currents to be switched rapidly. It also reduces internal
ringing that can cause voltage breakdown when the
driver is operated at or near the maximum rated voltage.
Internal ringing can also cause output oscillation due to
feedback. This feedback is added to the input signal
since it is referenced to the same ground.
CONT ROL 1 80° T O 3 60 °
Micrel Inc.
January 2011
C ONT R OL 0° TO 180°
CONDUCTION ANGLE
CONDUCTION ANGLE
φ 1 D R I V E S I G N A L
0.1µF
50V
0.1µF
WIMA
M KS2
2
+15
MIC4451
1
4
Figure 3. Direct Motor Drive
8
5
D R I V E
LOGIC
+
(x2) 1N4448
6, 7
U NI TE D CH EM CO N S X E
1µF
50V
MKS2
5.6 kΩ
560 Ω
MIC4451
MIC4452
V DD
V DD
560µF 50V
PHASE 1 OF 3 PHASE MOTOR
D R I VER U SI N G M I C 44 51 / 44 52
1 µ F
1 µ F
φ
+
1
100µF 50V
Figure 4. Self Contained Voltage Doubler
BYV 10 (x 2)
M
φ
2
V DD
V DD
+
φ
3
8
To guarantee low supply impedance over a wide
frequency range, a parallel capacitor combination is
recommended for supply bypassing. Low inductance
ceramic disk capacitors with short lead lengths (< 0.5
inch) should be used. A 1µF low ESR film capacitor in
parallel with two 0.1µF low ESR ceramic capacitors,
(such as AVX RAM GUARD
bypassing. Connect one ceramic capacitor directly
between pins 1 and 4. Connect the second ceramic
capacitor directly between pins 8 and 5.
Grounding
The high current capability of the MIC4451/4452
demands careful PC board layout for best performance.
Since the MIC4451 is an inverting driver, any ground
lead impedance will appear as negative feedback which
can degrade switching speed. Feedback is especially
noticeable with slow-rise time inputs. The MIC4451 input
structure includes 200mV of hysteresis to ensure clean
transitions and freedom from oscillation, but attention to
layout is still recommended.
Figure 5 shows the feedback effect in detail. As the
MIC4451 input begins to go positive, the output goes
negative and several amperes of current flow in the
ground lead. As little as 0.05Ω of PC trace resistance
can produce hundreds of millivolts at the MIC4451
ground pins. If the driving logic is referenced to power
ground, the effective logic input level is reduced and
oscillation may result.
To insure optimum performance, separate ground traces
should be provided for the logic and power connections.
Connecting the logic ground directly to the MIC4451
GND pins will ensure full logic drive to the input and
ensure fast output switching. Both of the MIC4451 GND
pins should, however, still be connected to power
ground.
®
), provides adequate
MIC4451/4452
M9999-011811