IR3502MTRPBF International Rectifier, IR3502MTRPBF Datasheet - Page 17

• Manufacturer Part Number: IR3502MTRPBF
• Description: IC XPHASE3 CONTROLLER 32-MLPQ
• Manufacturer: International Rectifier
• Series: XPhase3™r

Specifications of IR3502MTRPBF

• Applications: Processor
• Current - Supply: 8mA
• Voltage - Supply: 8 V ~ 16 V
• Operating Temperature: 0°C ~ 100°C
• Mounting Type: Surface Mount
• Package / Case: 32-MLPQ
• Package: 32-Lead MLPQ
• Circuit: X-Phase Control IC
• Switch Freq (khz): 250kHz to 1.5MHz
• Pbf: PbF Option Available
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: IR3502MTRPBFTR

Start-up Sequence
The IR3502 has a programmable soft-start function to limit the surge current during the converter start-up. A
capacitor connected between the SS/DEL and LGND pins controls soft start timing, over-current protection delay
and hiccup mode timing. A charge current of 52.5uA and discharge current of 4uA control the up slope and down
slope of the voltage at the SS/DEL pin respectively. Figure 9 depicts start-up sequence of converter with VR 11.1
VID. If there is no fault, as the ENABLE is asserted, the SS/DEL pin will start charging. The error amplifier output
EAOUT is clamped low until SS/DEL reaches 1.4V. The error amplifier will then regulate the converter’s output
voltage to match the SS/DEL voltage less the 1.4V offset until the converter output reaches the 1.1V boot voltage.
The SS/DEL voltage continues to increase until it rises above the 3.0V threshold of VID delay comparator. The VID
set inputs are then activated and VDAC pin transitions to the level determined by the VID inputs. The SS/DEL
voltage continues to increase until it rises above 3.92V and allows the VRRDY signal to be asserted. SS/DEL finally
settles at 4.0V, indicating the end of the soft start. The remote sense amplifier has a very low operating range of 50
mV in order to achieve a smooth soft start of output voltage without bump.
The VCCL under voltage lock-out, VID fault modes, over current, as well as a low signal on the ENABLE input
immediately sets the fault latch, which causes the EAOUT pin to drive low turning off the phase IC drivers. The
VRRDY pin also drives low and SS/DEL begin to discharge until the voltage reaches 0.2V. If the fault has cleared
the fault latch will be reset by the discharge comparator allowing a normal soft start to occur.
Other fault conditions, such as over voltage, open sense lines, open loop monitor, and open daisy chain, set
different fault latches, which start discharging SS/DEL, pull down EAOUT voltage and drive VRRDY low. However,
the latches can only be reset by cycling VCCL power.
Page 17 of 39
+
-
VDAC
Buffer
Control IC
VDAC1
Remote
Sense
Amplifier
Figure 8 Adaptive voltage positioning with thermal compensation.
Thermal
Comp
Amplifier
100k
+
-
+
-
Error
Amplifier
200k
+
-
EAOUT
FB
IIN
VDAC
VDRP
DAC_BUFF
VN
VO
VOSEN+
VOSEN-
RTCMP1
RDRP
RTCMP3
RTCMP2
RFB
RTHERM
VDAC
VDAC
IOUT
IOUT
Phase IC
Phase IC
3k
3k
July 28, 2009
IR3502
Current
Sense
Amplifier
Current
Sense
Amplifier
+
+
-
-
CSIN+
CSIN+
CSIN-
CSIN-