AD595CQ Analog Devices Inc, AD595CQ Datasheet - Page 8

• Manufacturer Part Number: AD595CQ
• Description: IC THERMOCOUPLE A W/COMP 14CDIP
• Manufacturer: Analog Devices Inc
• Type: Low Powerr

Specifications of AD595CQ

• Rohs Status: RoHS non-compliant
• Function: Thermocouple Amplifier
• Topology: Ice Point Compensation, Overload Detection
• Sensor Type: External
• Output Type: Voltage
• Output Alarm: Yes
• Output Fan: No
• Voltage - Supply: 5 V ~ ±15 V
• Operating Temperature: -55°C ~ 125°C
• Mounting Type: Through Hole
• Package / Case: 14-CDIP (0.300", 7.62mm)
• Ic Output Type: Voltage
• Sensing Accuracy Range: ± 1°C
• Supply Current: 160µA
• Supply Voltage Range: 5V To 30V
• Sensor Case Style: DIP
• No. Of Pins: 14
• Termination Type: DIP
• Amplifier Type: Instrumentation
• Bandwidth: 15 kHz
• Converter Type: Monolithic theremocouple amplifier
• Current, Input Bias: 0.1 μA
• Current, Output: ±5 mA
• Current, Quiescent Supply: 160 uA (Typ.) @ 25 °C
• Current, Supply: 160 μA
• Package Type: CDIP-14
• Temperature, Operating, Maximum: 125 °C
• Temperature, Operating, Minimum: -55 °C
• Temperature, Operating, Range: -55 to +125 °C
• Voltage, Supply: +5 to ±15 V
• Low Impedance Voltage Output: 10 mV⁄°C
• Wide Power Supply Range: + 5 V to 615 V
• Low Power: 1 mW typical
• Filter Terminals: DIP
• Rohs Compliant: No
• Accuracy: ± 1
• Accuracy %: 1%
• Sensing Temperature: -
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

AD594/AD595
THERMOCOUPLE BASICS
Thermocouples are economical and rugged; they have reason-
ably good long-term stability. Because of their small size, they
respond quickly and are good choices where fast response is im-
portant. They function over temperature ranges from cryogenics
to jet-engine exhaust and have reasonable linearity and accuracy.
Because the number of free electrons in a piece of metal de-
pends on both temperature and composition of the metal, two
pieces of dissimilar metal in isothermal and contact will exhibit
a potential difference that is a repeatable function of tempera-
ture, as shown in Figure 14. The resulting voltage depends on
the temperatures, T1 and T2, in a repeatable way.
Since the thermocouple is basically a differential rather than
absolute measuring device, a know reference temperature is
required for one of the junctions if the temperature of the other
is to be inferred from the output voltage. Thermocouples made
of specially selected materials have been exhaustively character-
ized in terms of voltage versus temperature compared to primary
temperature standards. Most notably the water-ice point of 0 C
is used for tables of standard thermocouple performance.
An alternative measurement technique, illustrated in Figure 15,
is used in most practical applications where accuracy requirements
do not warrant maintenance of primary standards. The reference
junction temperature is allowed to change with the environment
of the measurement system, but it is carefully measured by some
type of absolute thermometer. A measurement of the thermo-
couple voltage combined with a knowledge of the reference
temperature can be used to calculate the measurement junction
temperature. Usual practice, however, is to use a convenient
thermoelectric method to measure the reference temperature
Figure 14. Thermocouple Voltage with 0 C Reference
TEMPERATURE
0.035 0.010
(0.89 0.25)
0.125
(3.18)
UNKNOWN
(1.02) R
MIN
0.040
0.047 0.007
(1.19 0.18) 0.017
T1
14
CONSTANTAN
1
PIN 1
(
0.430 (10.92)
(17.78 0.25)
0.43 +0.08
0.700 0.010
+0.003
–0.002
–0.05
TO-116 (D) Package
Cu
(
(2.54)
0.100
BSC
IRON
8
7
0.265
(6.73)
0.085 (2.16)
Cu
0.180 0.030
(4.57 0.76)
CONSTANTAN
V1
0.290 0.010
(7.37 0.25)
0.30 (7.62) REF
(7.87 0.25)
0.31 0.01
T2
Dimensions shown in inches and (mm).
REFERENCE
ICE POINT
OUTLINE DIMENSIONS
0.095 (2.41)
0.01 0.002
(0.25 0.05)
–8–
and to arrange its output voltage so that it corresponds to a ther-
mocouple referred to 0 C. This voltage is simply added to the
thermocouple voltage and the sum then corresponds to the stan-
dard voltage tabulated for an ice-point referenced thermocouple.
The temperature sensitivity of silicon integrated circuit transis-
tors is quite predictable and repeatable. This sensitivity is
exploited in the AD594/AD595 to produce a temperature re-
lated voltage to compensate the reference of “cold” junction of a
thermocouple as shown in Figure 16.
Since the compensation is at the reference junction temperature,
it is often convenient to form the reference “junction” by connect-
ing directly to the circuit wiring. So long as these connections
and the compensation are at the same temperature no error will
result.
3.175)
0.125
(0.812)
MIN
(7.87)
0.032
0.310
Figure 15. Substitution of Measured Reference
Temperature for Ice Point Reference
14
Figure 16. Connecting Isothermal Junctions
CONSTANTAN
T1
1
T1
PIN 1
(19.55 0.39)
0.600 (15.24)
0.77 0.015
(0.457)
0.018
BSC
CONSTANTAN
Cu
IRON
Cerdip (Q) Package
IRON
8
7
V2
0.100
(2.54)
BSC
0.260 0.020
(6.6 0.51)
0.035 0.010
(0.889 0.254)
V1
'
Cu
SEATING
PLANE
0.180 0.030
(4.57 0.76)
CuNi–
Cu
Cu
V1
T3
15
T3
0
0.300 (7.62)
V
FOR PROPERLY
SCALED V
1
REF
'
= V
0.010 0.001
(0.254 0.025)
1
3
'
= f(T
V3
0.148 0.015
(3.76 0.38)
'
3
)
REV. C