LT1375IS8#PBF Linear Technology, LT1375IS8#PBF Datasheet - Page 25

• Manufacturer Part Number: LT1375IS8#PBF
• Description: IC SW REG 1.5A ADJ STP-DWN 8SOIC
• Manufacturer: Linear Technology
• Type: Step-Down (Buck)r

Specifications of LT1375IS8#PBF

• Internal Switch(s): Yes
• Synchronous Rectifier: No
• Number Of Outputs: 1
• Voltage - Output: 2.42 ~ 21.5 V
• Current - Output: 1.5A
• Frequency - Switching: 500kHz
• Voltage - Input: 5 ~ 25 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Dc To Dc Converter Type: Step Down
• Pin Count: 8
• Input Voltage: 25V
• Output Voltage: 2.42 to 21.5V
• Switching Freq: 560kHz
• Output Current: 1.5A
• Package Type: SOIC N
• Output Type: Adjustable
• Switching Regulator: Yes
• Line Regulation: 0.03%/V
• Mounting: Surface Mount
• Input Voltage (min): 5V
• Operating Temperature Classification: Automotive
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Power - Output: -
• Lead Free Status / Rohs Status: Compliant

INDUCTOR VALUE
Unlike buck converters, positive-to-negative converters
cannot use large inductor values to reduce output ripple
voltage. At 500kHz, values larger than 25µH make almost
no change in output ripple. The graph in Figure 19 shows
peak-to-peak output ripple voltage for a 5V to – 5V con-
verter versus inductor value. The criteria for choosing the
inductor is therefore typically based on ensuring that peak
switch current rating is not exceeded. This gives the
lowest value of inductance that can be used, but in some
cases (lower output load currents) it may give a value that
creates unnecessarily high output ripple voltage. A com-
promise value is often chosen that reduces output ripple.
As you can see from the graph, large inductors will not
give arbitrarily low ripple, but small inductors can give
high ripple.
The difficulty in calculating the minimum inductor size
needed is that you must first know whether the switcher
will be in continuous or discontinuous mode at the critical
point where switch current is 1.5A. The first step is to use
the following formula to calculate the load current where
the switcher must use continuous mode. If your load
current is less than this, use the discontinuous mode
formula to calculate minimum inductor needed. If load
current is higher, use the continuous mode formula.
Output current where continuous mode is needed:
APPLICATIONS
Figure 19. Ripple Voltage on Positive-to-Negative Converter
I
CONT
=
150
120
90
60
30
4
0
(
0
V
IN
+
U
5
V
OUT
( ) ( )
INDUCTOR SIZE (µH)
V
INFORMATION
IN
)
U
10
(
V
2
5V TO –5V CONVERTER
OUTPUT CAPACITOR
ESR = 0.1Ω
IN
I
P
+
I
LOAD
I
2
15
LOAD
V
OUT
= 0.25A
W
= 0.1A
20
+
1375/76 F19
V
F
)
25
U
Minimum inductor discontinuous mode:
Minimum inductor continuous mode:
For the example above, with maximum load current of
0.25A:
This says that discontinuous mode can be used and the
minimum inductor needed is found from:
In practice, the inductor should be increased by about
30% over the calculated minimum to handle losses and
variations in value. This suggests a minimum inductor of
3µH for this application, but looking at the ripple voltage
chart shows that output ripple voltage could be reduced by
a factor of two by using a 15µH inductor. There is no rule
of thumb here to make a final decision. If modest ripple is
needed and the larger inductor does the trick, go for it. If
ripple is noncritical use the smaller inductor. If ripple is
extremely critical, a second filter may have to be added in
any case, and the lower value of inductance can be used.
Keep in mind that the output capacitor is the other critical
factor in determining output ripple voltage. Ripple shown
on the graph (Figure 19) is with a capacitor ESR of 0.1Ω.
This is reasonable for an AVX type TPS “D” or “E” size
I
L
L
L
CONT
MIN
MIN
MIN
=
=
=
=
2
2
⎛
⎝
( )( )
( )
500 10
V
f V
4 5 5 5 5 0 5
( )( )
OUT
( )
(
2 5 0 25
f I
( )( )
IN
•
+
P
( ) ( )
+
5 1 5
I
2
OUT
3
V
2
(
.
⎞
⎠
OUT
( )
+ +
1 5
.
.
)
⎡
⎢
⎢
⎣
( )( )
2
I
V
2
P
IN
−
=
.
LT1375/LT1376
I
2 2
OUT
V
)
. µ
OUT
=
⎛
⎜
⎜
⎝
0 37
H
1
.
+
(
A
V
OUT
V
IN
+
25
V
F
)
13756fd
⎞
⎟
⎟
⎠
⎤
⎥
⎥
⎦