OPTOCOUPLER TRANS-OUT 1MBD 8-DIP

HCPL-4504-000E

Manufacturer Part NumberHCPL-4504-000E
DescriptionOPTOCOUPLER TRANS-OUT 1MBD 8-DIP
ManufacturerAvago Technologies US Inc.
HCPL-4504-000E datasheet
 


Specifications of HCPL-4504-000E

Input TypeDCPackage / Case8-DIP (0.300", 7.62mm)
Voltage - Isolation3750VrmsNumber Of Channels1, Unidirectional
Current - Output / Channel8mAPropagation Delay High - Low @ If200ns @ 16mA
Current - Dc Forward (if)25mAOutput TypeOpen Collector
Mounting TypeThrough HoleIsolation Voltage3750 Vrms
Maximum Continuous Output Current8 mAMaximum Forward Diode Current25 mA
Output DeviceTransistor With BaseConfiguration1 Channel
Current Transfer Ratio65 %Maximum Baud Rate1 MBps
Maximum Forward Diode Voltage1.7 VMaximum Reverse Diode Voltage5 V
Maximum Input Diode Current25 mAMaximum Power Dissipation100 mW
Maximum Operating Temperature+ 100 CMinimum Operating Temperature- 55 C
No. Of Channels1Optocoupler Output TypePhototransistor
Input Current16mAOutput Voltage20V
Opto Case StyleDIPNo. Of Pins8
Ctr Min26%Common Mode Ratio10k
Rohs CompliantYesLead Free Status / RoHS StatusLead free / RoHS Compliant
Other names516-1479-5  
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
9
Page 9
10
Page 10
11
12
13
14
15
16
17
18
19
Page 1/19

Download datasheet (195Kb)Embed
Next
HCPL-4504/J454/0454, HCNW4504
High CMR, High Speed Optocouplers
Data Sheet
Lead (Pb) Free
RoHS 6 fully
compliant
RoHS 6 fully compliant options available;
-xxxE denotes a lead-free product
Description
The HCPL-4504 and HCPL-0454 contain a GaAsP LED
while the HCPL-J454 and HCNW4504 contain an AlGaAs
LED. The LED is optically coupled to an integrated high
gain photo detector.
The HCPL-4504 series has short propagation delays and
high CTR. The HCPL-4504 series also has a guaranteed
propagation delay diff erence (t
-t
PLH
make the HCPL-4504 series an excellent solution to IPM
inverter dead time and other switching problems. The
CTR, propagation delay, and CMR are specifi ed both for
TTL and IPM conditions which are provided for ease of
application. These single channel, diode-transistor opto-
couplers are available in 8-Pin DIP, SO-8, and Widebody
package confi gurations. An insulating layer between a
LED and an integrated photodetector provide electrical
insulation between input and output. Separate connec-
tions for the photodiode bias and output-transistor col-
lector increase the speed up to a hundred times that of
a conventional phototransistor coupler by reducing the
base collector capacitance.
Functional Diagram
8
NC
1
V
CC
7
ANODE
2
NC
6
CATHODE
3
V
O
5
NC
4
GND
A 0.1 μF bypass capacitor between pins 5 and 8 is recommended.
Schematic
I
CC
8
V
CC
I
F
+
ANODE
2
V
F
I
6
O
V
O
CATHODE
3
5
SHIELD
GND
CAUTION: It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and/or degradation which may be induced by ESD.
Features
• Short propagation delays for TTL and IPM applications
• 15 kV/μs minimum Common Mode Transient immu-
nity at V
= 1500 V for TTL/load drive
CM
• High CTR at T
>25% for HCPL-4504/0454
>23% for HCNW4504
>19% for HCPL-J454
). These features
PHL
• Electrical specifi cations for common IPM applications
• TTL compatible
• Open collector output
• Safety approval:
UL recognized
– 3750 V rms/1min. for HCPL-4504/0454/J454
– 5000 V rms/1min. for HCPL-4504 Option 020 and
HCNW4504
CSA approved
IEC/EN/DIN EN 60747-5-2 approved
– V
= 560 Vpeak for HCPL-0454 Option 060
IORM
– V
= 630 Vpeak for HCPL-4504 Option 060
IORM
– V
= 891 Vpeak for HCPL-J454
IORM
– V
= 1414 Vpeak for HCNW4504
IORM
Applications
• Inverter circuits and Intelligent Power Module (IPM)
TRUTH TABLE
interfacing: High Common Mode Transient immunity
LED
V
O
(> 10 kV/μs for an IPM load/drive) and (t
ON
LOW
Specifi ed (see Power Inverter Dead Time section)
OFF
HIGH
• Line receivers: Short propagation delays and low in-
put-output capacitance
• High speed logic ground isolation: TTL/TTL, TTL/
CMOS, TTL/LSTTL
• Replaces pulse transformers: Save board space and
weight
• Analog signal ground isolation: Integrated photode-
tector provides improved linearity over phototransis-
tors
= 25°C
A
- t
)
PLH
PHL

HCPL-4504-000E Summary of contents

  • Page 1

    ... Electrical specifi cations for common IPM applications • TTL compatible • Open collector output • Safety approval: UL recognized – 3750 V rms/1min. for HCPL-4504/0454/J454 – 5000 V rms/1min. for HCPL-4504 Option 020 and HCNW4504 CSA approved IEC/EN/DIN EN 60747-5-2 approved – 560 Vpeak for HCPL-0454 Option 060 IORM – ...

  • Page 2

    ... To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: HCPL-4504-560E to order product of 300 mil DIP Gull Wing Surface Mount package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-2 Safety Approval and RoHS compliant. Example 2: HCPL-4504 to order product of 300 mil DIP package in Tube packaging and non RoHS compliant ...

  • Page 3

    ... TYPE NUMBER A XXXXZ R U YYWW 1.19 (0.047) MAX. 3.56 ± 0.13 (0.140 ± 0.005) 1.080 ± 0.320 (0.043 ± 0.013) HCPL-4504 Gull Wing Surface Mount Option 300 Outline Drawing 9.65 ± 0.25 (0.380 ± 0.010 1.19 (0.047) MAX. 1.080 ± 0.320 (0.043 ± ...

  • Page 4

    ... TYPE NUMBER A XXXX R U YYWW 1.19 (0.047) MAX. 3.56 ± 0.13 (0.140 ± 0.005) 1.080 ± 0.320 (0.043 ± 0.013) HCPL-J454 Gull Wing Surface Mount Option 300 Outline Drawing 9.80 ± 0.25 (0.386 ± 0.010 1.19 (0.047) MAX. 1.080 ± 0.320 (0.043 ± ...

  • Page 5

    ... MAX. [1.080] 0.320 0.043 0.013 0.100 DIMENSIONS IN [MILLIMETERS] INCHES OPTION NUMBERS 400 AND 600 NOT MARKED. NOTE: FLOATING LEAD PROTRUSION IS 0.5 mm (20 mils) MAX. HCPL-0454 Outline Drawing (8-Pin Small Outline Package XXX 3.937 ± 0.127 YWW (0.155 ± 0.005) ...

  • Page 6

    HCNW4504 Outline Drawing (8-Pin Widebody Package) 11.15 ± 0.15 (0.442 ± 0.006 HCNWXXXX YYWW 2.54 (0.100) TYP. 1.78 ± 0.15 (0.070 ± 0.006) HCNW4504 Gull Wing Surface Mount Option 300 Outline Drawing 11.15 ...

  • Page 7

    Solder Refl ow Temperature Profi le 300 PREHEATING RATE 3 ° °C/–0.5 °C/SEC. REFLOW HEATING RATE 2.5 °C ± 0.5 °C/SEC. 200 160 °C 150 °C 140 °C 3 ° °C/–0.5 °C 100 ROOM TEMPERATURE 0 ...

  • Page 8

    ... Vrms / 1 minute, 1 minute Option 020 5000 Vrms / 1 minute Option 060 V = 891 IORM V = 630 Vpeak Vpeak IORM Value HCPL- HCPL-J454 J454 All other HCPL- HCNW -400E/-600E options 0454 4504 8.0 7.4 4.9 9.6 8.0 8.0 4.8 10.0 0.5 0.5 0.08 1.0 ...

  • Page 9

    ... PR V 840 945 PR V 4000 6000 IOTM T 150 175 S I 150 230 S,INPUT P 600 600 S,OUTPUT ≥10 ≥10 S HCPL-J454 HCNW4504 Unit I-IV I-IV I-IV I-IV I-III I-IV I-III I-IV I-III 55/100/21 55/85/ 891 1414 V peak 1670 2652 V peak 1336 2121 V peak ...

  • Page 10

    ... HCPL-4504 -55 A HCPL-0454 HCPL-J454 HCNW4504 -55 I F(AVG) I HCPL-4504 F(PEAK) HCPL-0454 HCPL-J454 HCNW4504 I HCPL-4504 F(TRANS) HCPL-0454 HCPL-J454 HCNW4504 V HCPL-4504 R HCPL-0454 HCPL-J454 HCNW4504 P HCPL-4504 IN HCPL-0454 HCPL-J454 HCNW4504 I O(AVG) I O(PEAK HCPL-4504 LS HCPL-J454 HCNW4504 T HCPL-0454, See Package Outline Drawings RP Option 300 , Option 500, Option 400E & ...

  • Page 11

    ... Supply HCPL-0454 Current HCNW4504 HCPL-J454 Logic High I CCH Supply Current Input Forward V HCPL-4504 F Voltage HCPL-0454 HCPL-J454 HCNW4504 Input Reverse BV HCPL-4504 R Breakdown HCPL-0454 Voltage HCPL-J454 HCNW4504 Temperature ∆V HCPL-4504 F Coeffi cient HCPL-0454 ∆ Forward HCPL-J454 Voltage HCNW4504 Input C HCPL-4504 IN Capacitance HCPL-0454 ...

  • Page 12

    ... PLH Diff erence Be- t PHL tween Any 2 Parts Common Mode | Transient Immu- nity at Logic High | Level Output | Common Mode Transient Immu- |CM | HCPL- L nity at Logic Low J454 Level Output Others 10 | *All typicals 25° Min. Typ. Max. Units Test Conditions 0.2 0.3 μ 25° ...

  • Page 13

    ... HCPL-0454 Withstand HCPL-J454 Voltage† HCPL-4504 Option 020 HCNW4504 Input-Output R HCPL-4504 I-O Resistance HCPL-0454 HCPL-J454 HCNW4504 Capacitance C HCPL-4504 I-O (Input-Output) HCPL-0454 HCPL-J454 HCNW4504 All typicals 25°C.. A †The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics Table (if applicable), your equipment level safety specifi ...

  • Page 14

    ... V – FORWARD VOLTAGE – VOLTS F Figure 3. Input current vs. forward voltage. 14 HCPL-J454 25° 5 – OUTPUT VOLTAGE – HCPL-J454 2.0 NORMALIZED 25° 1.0 0 – INPUT CURRENT – HCPL-J454/HCNW4504 1000 T = 25°C A 100 – 1.0 0.1 ...

  • Page 15

    ... V V THHL THLH PHL PLH Figure 6. Switching test circuit 90% 90 10% 10 SWITCH SWITCH mA Figure 7. Test circuit for transient immunity and typical waveforms. 15 HCPL-J454 1.05 NORMALIZED 25° 0.95 0.9 0.85 -60 -40 - 100 T – TEMPERATURE – ° PULSE F 1 GEN Ω ...

  • Page 16

    ... 1.5 V THHL THLH 1.0 10% DUTY CYCLE t PLH 0.8 0 PHL 0 0.2 0 – LOAD RESISTANCE – kΩ L Figure 9. Propagation delay time vs. load resis- tance. HCPL-J454/HCNW4504 1 15 kΩ 1 100 1.5 V THHL t PLH V = 2.0 V THLH 0.8 50% DUTY CYCLE 0.7 0.6 0.5 t PHL 0.4 0.3 ...

  • Page 17

    ... LED Figure 16. Typical power inverter. 17 HCPL-0454 OPTION 060/HCNW4504 1000 P (mW) for HCNW4504 S 900 I (mA) for HCNW4504 S P (mW) for HCPL-0454 S 800 OPTION 060 I (mA) for HCPL-0454 700 S OPTION 060 600 500 400 300 200 (150) 100 100 125 150 175 T – CASE TEMPERATURE – °C ...

  • Page 18

    ... Figure 17. LED delay and dead time diagram. Power Inverter Dead Time and Propagation Delay Specifi ca- tions The HCPL-4504/0454/J454 and HCNW4504 include a specifi ca tion intended to help designers minimize “dead time” in their power inverter designs. The new “propaga- tion delay diff erence” specifi cation (t deter min ing not only how much optocoupler switch- ing delay is needed to prevent “ ...

  • Page 19

    ... Therefore, opto coup lers with tight propagation delay specifi cations (and not just shorter delays or lower pulse- width distortion) can achieve short dead times in power inverters. The HCPL-4504/0454/J454 and HCNW4504 specify a minimum (t ing temperature range of 0-70°C, resulting in a maximum dead time of 2.0 μ ...