HCPL-4504#520 Avago Technologies US Inc., HCPL-4504#520 Datasheet - Page 8

• Manufacturer Part Number: HCPL-4504#520
• Description: OPTOCOUPLER 1CH UL GAASP 8-SMD
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-4504#520

• Input Type: DC
• Package / Case: 8-SMD (300 mil)
• Voltage - Isolation: 5000Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 8mA
• Propagation Delay High - Low @ If: 200ns @ 16mA
• Current - Dc Forward (if): 25mA
• Output Type: Open Collector
• Mounting Type: Surface Mount, Gull Wing
• Isolation Voltage: 3750 Vrms
• Output Device: Phototransistor
• Configuration: 1 Channel
• Current Transfer Ratio: 65 %
• Maximum Baud Rate: 1 MBps
• Maximum Forward Diode Voltage: 1.7 V
• Maximum Reverse Diode Voltage: 5 V
• Maximum Input Diode Current: 25 mA
• Maximum Power Dissipation: 100 mW
• Maximum Operating Temperature: + 100 C
• Minimum Operating Temperature: - 55 C
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Regulatory Information
The devices contained in this data sheet have been approved by the following agencies:
Insulation and Safety Related Specifi cations
All Avago data sheets report the creepage and clearance
inherent to the optocoupler component itself. These di-
mensions are needed as a starting point for the equip-
ment designer when determining the circuit insulation
requirements.
However, once mounted on a printed circuit board, mini-
mum creepage and clearance requirements must be
met as specifi ed for individual equipment standards. For
8
Agency/Standard
Underwriters Laboratories (UL)
Recognized under UL1577,
Component Recognition Program,
Category FPQU2, File E55361
Canadian Standards Association (CSA)
File CA88324
IEC/EN/DIN EN 60747-5-2
Approved under:
IEC 60747-5-2:1997 + A1:2002
EN 60747-5-2:2001 + A1:2002
DIN EN 60747-5-2 (VDE 0884 Teil 2):2003-01
Parameter
Minimum External
Air Gap
(External Clearance)
Minimum External
Tracking
(External Creepage)
Minimum Internal
Plastic Gap
(Internal Clearance)
Minimum Internal
Tracking (Internal
Creepage)
Tracking Resistance
(Comparative
Tracking Index)
Isolation Group
Symbol
L(101)
L(102)
CTI
HCPL-
≥175
4504
0.08
7.1
7.4
NA
IIIa
UL1577
Component
Acceptance
Notice #5
-400E/-600E
HCPL-
≥175
J454
8.0
8.0
0.5
NA
IIIa
HCPL-4504
3750 Vrms /
1 minute,
Option 020 5000
Vrms / 1 minute
3750 Vrms /
1 minute,
Option 020 5000
Vrms / 1 minute
Option 060
V
IORM
HCPL-J454
Value
All other
options
≥175
= 630 Vpeak
7.4
8.0
0.5
NA
IIIa
creepage, the shortest distance path along the surface
of a printed circuit board between the solder fi llets of
the input and output leads must be considered. There
are recommended techniques such as grooves and ribs
which may be used on a printed circuit board to achieve
desired creepage and clearances. Creepage and clear-
ance distances will also change depending on factors
such as pollution degree and insulation level.
HCPL-
≥175
0454
0.08
4.9
4.8
NA
IIIa
HCPL-J454
3750 Vrms /
1 minute
3750 Vrms /
1 minute
V
Vpeak
IORM
HCNW
≥200
4504
10.0
9.6
1.0
4.0
IIIa
= 891
Units Conditions
mm
mm
mm
mm
Volts
HCPL-0454
3750 Vrms /
1 minute
3750 Vrms /
1 minute
Option 060
V
Vpeak
IORM
Measured from input ter-
minals to output terminals,
shortest distance through air.
Measured from input ter-
minals to output terminals,
shortest distance path along
body.
Through insulation distance,
conductor to conductor,
usually the direct distance
between the photoemitter
and photodetector inside the
optocoupler cavity.
Measured from input ter-
minals to output terminals,
along internal cavity.
DIN IEC 112/VDE 0303 Part 1
Material Group (DIN VDE
0110, 1/89, Table 1)
= 560
HCNW4504
5000 Vrms /
1 minute
5000 Vrms /
1 minute
V
Vpeak
IORM
= 1414