OPTOCOUPLER T-OUT 1MBD 8-DIP

HCPL-4503

Manufacturer Part NumberHCPL-4503
DescriptionOPTOCOUPLER T-OUT 1MBD 8-DIP
ManufacturerAvago Technologies US Inc.
HCPL-4503 datasheets
 


Specifications of HCPL-4503

Input TypeDCPackage / Case8-DIP (0.300", 7.62mm)
Voltage - Isolation3750VrmsNumber Of Channels1, Unidirectional
Current - Output / Channel8mAData Rate1Mbps
Propagation Delay High - Low @ If200ns @ 16mACurrent - Dc Forward (if)25mA
Output TypeOpen CollectorMounting TypeThrough Hole
Isolation Voltage3750 VrmsOutput DevicePhototransistor
Configuration1 ChannelCurrent Transfer Ratio25 %
Maximum Baud Rate1 MBpsMaximum Forward Diode Voltage1.7 V
Maximum Reverse Diode Voltage5 VMaximum Input Diode Current25 mA
Maximum Power Dissipation100 mWMaximum Operating Temperature+ 70 C
Minimum Operating Temperature0 CPackage Type8-Pin DIP
Lead Free Status / RoHS StatusContains lead / RoHS non-compliantOther names516-1032-5
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
9
Page 9
10
Page 10
11
12
13
14
15
16
Page 1/16

Download datasheet (650Kb)Embed
Next
HCNW4502/3
HCPL-0452/0453/4502/4503
Single Channel, High Speed Optocouplers
Data Sheet
Lead (Pb) Free
RoHS 6 fully
compliant
RoHS 6 fully compliant options available;
-xxxE denotes a lead-free product
Description
These diode-transistor optocouplers use an insulating
layer between a LED and an integrated photodetector to
provide electrical insulation between input and output.
Separate connections for the photodiode bias and out-
put-transistor collector increase the speed up to a hun-
dred times that of a conventional phototransistor coupler
by reducing the base-collector capacitance.
These single channel optocouplers are available in
8-Pin DIP, SO-8 and Widebody package configurations.
The HCPL-4502/4503 and HCNW4502/4503 are designed
for high speed TTL/TTL applications. A standard 16 mA TTL
sink current through the input LED will provide enough
output current for 1 TTL load and a 5.6 kΩ pull-up resistor.
CTR for these devices is 19% minimum at I
Functional Diagram
NC
V
8
1
CC
ANODE
NC
2
7
CATHODE
V
6
3
o
NC
GND
4
5
A 0.1 µF bypass capacitor must be connected between pins 5 and 8.
CAUTION: It is advised that normal static precautions be taken in handling and assembly
of this component to prevent damage and/or degradation which may be induced by ESD.
Features
• 15 kV/µs minimum common mode transient
immunity at V
• High speed: 1 Mb/s
• TTL compatible
• Available in 8-Pin DIP, SO-8, widebody packages
• Open collector output
• Guaranteed performance from temperature:
0°C to 70°C
• Safety approval
UL Recognized – 3750 V
for 1 minute for HCNW and Option 020 devices)
per UL1577
CSA Approved
IEC/EN/DIN EN 60747-5-2 Approved
= 16 mA.
F
– V
IORM
– V
IORM
• Dual channel version available (4534/0534)
• MIL-PRF-38534 hermetic version available
TRUTH TABLE
(55XX/65XX/4N55)
(POSITIVE LOGIC)
LED
V
o
Applications
ON
LOW
OFF
HIGH
• High voltage insulation
• Video signal isolation
• Power transistor isolation in motor drives
• Line receivers
• Feedback element in switched mode power supplies
• High speed logic ground isolation
– TTL/TTL, TTL/CMOS, TTL/LSTTL
• Replaces pulse transformers
• Replaces slow phototransistor isolators
• Analog signal ground isolation
= 1500 V
CM
for 1 minute (5000 V
rms
= 630 V peak for HCPL-4503#060
= 1414 V peak for HCNW devices
rms

HCPL-4503 Summary of contents

  • Page 1

    ... Feedback element in switched mode power supplies • High speed logic ground isolation – TTL/TTL, TTL/CMOS, TTL/LSTTL • Replaces pulse transformers • Replaces slow phototransistor isolators • Analog signal ground isolation = 1500 V CM for 1 minute (5000 V rms = 630 V peak for HCPL-4503#060 = 1414 V peak for HCNW devices rms ...

  • Page 2

    ... The HCPL-4502, HCPL-0452, and HCNW4502 provide the electrical and switching performance of the 6N136, HCPL- 0501, and HCNW136 with increased ESD protection. The HCPL-4503, HCPL-0453, and HCNW4503 are similar to the HCPL-4502, HCPL-0452, and HCNW4502 optocouplers but have increased common mode transient immunity of 15 kV/µ ...

  • Page 3

    ... Ordering Information HCPL-4502 and HCPL-4503, HCPL-0452, HCPL-0453 are UL Recognized with 3750 Vrms for 1 minute per UL1577. HCNW4502 and HCNW4503 are UL Recognized with 5000 Vrms for 1 minute per UL1577. All devices above listed are approved under CSA Component Acceptance Notice #5, File CA 88324. ...

  • Page 4

    ... MAX. (0.043 ± 0.013) 2.54 ± 0.25 (0.100 ± 0.010) 8-Pin DIP Package with Gull Wing Surface Mount Option 300 (HCPL-4502/3) 9.65 ± 0.25 (0.380 ± 0.010 (0.250 ± 0.010) ...

  • Page 5

    ... Small Outline SO-8 Package (HCPL-0452/ 5.994 ± 0.203 (0.236 ± 0.008) XXX 3.937 ± 0.127 YWW (0.155 ± 0.005) PIN ONE 0.406 ± 0.076 1.270 (0.016 ± 0.003) (0.050) * 5.080 ± 0.127 (0.200 ± 0.005) 3.175 ± 0.127 (0.125 ± 0.005) 1 ...

  • Page 6

    Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW4502/3) 11.15 ± 0.15 (0.442 ± 0.006 (0.354 ± 0.006 1.55 (0.061) MAX. 1.78 ± 0.15 (0.070 ± 0.006) 2.54 (0.100) ...

  • Page 7

    Recommended Pb-Free IR Profile * 260 +0/-5°C Tp 217°C TL RAMP-UP 3°C/SEC. MAX. 150 - 200°C T smax T smin ts PREHEAT 60 to 180 SEC 25°C to PEAK TIME Regulatory Information The devices contained in this data ...

  • Page 8

    ... IOTM T 175 S I 230 S,INPUT P 600 S,OUTPUT R ≥ Symbol V IORM = 1 sec IOTM S,INPUT P S,OUTPUT R S HCPL-0452/0453 Units I-III 55/100/21 2 560 V peak 1050 V peak 840 V peak 4000 V peak 175 °C 150 mA 600 mW ≥10 Ω 9 Characteristic Units I-IV I-III 55/85/21 2 1414 V peak ...

  • Page 9

    Absolute Maximum Ratings Parameter Storage Temperature Operating Temperature Average Forward Input Current Peak Forward Input Current (50% duty cycle pulse width) (50% duty cycle pulse width) Peak Transient Input Current (≤1 µs pulse width, 300 pps) ...

  • Page 10

    ... Electrical Specifications (DC) Over recommended temperature (T A Parameter Symbol Device Current CTR HCPL-4502/3 Transfer Ratio HCPL-0452/3 HCNW4502/3 Logic Low V HCPL-4502/3 OL Output Voltage HCPL-0452/3 HCNW4502/3 Logic High I OH Output Current Logic Low I CCL Supply Current Logic High I CCH Supply Current Input Forward V 8-Pin DIP ...

  • Page 11

    ... HCPL-4502 H Transient Im- HCPL-0452 munity at Logic HCNW4502 High Level HCPL-4503 Output HCPL-0453 HCNW4503 Common Mode |CM | HCPL-4502 L Transient Im- HCPL-0452 munity at Logic HCNW4502 Low Level HCPL-4503 Output HCPL-0453 HCNW4503 *All typicals 25° 0°C to 70°C unless otherwise specified Min. Typ.* Max. Units 0.2 0 25° ...

  • Page 12

    Package Characteristics Over recommended temperature (T Parameter Sym. Device Input-Output V 8-Pin DIP ISO Momentary SO-8 Withstand Widebody Voltage** 8-Pin DIP (Option 020) I 8-Pin DIP I-O Input-Output R 8-Pin DIP I-O Resistance SO-8 Widebody Input-Output C 8-Pin DIP I-O ...

  • Page 13

    ... PIN DIP, SO 25° 5 OUTPUT VOLTAGE - V O Figure 1. DC and pulsed transfer characteristics. 8 PIN DIP, SO-8 1.5 HCPL-4502/3, HCPL-0452/0453 1.0 0.5 0 INPUT CURRENT - mA F Figure 2. Current transfer ratio vs. input current. 8 PIN DIP, SO-8 1000 100 1.0 0.1 0.01 0.001 1 1 FORWARD VOLTAGE - VOLTS F Figure 3 ...

  • Page 14

    ... 0 0 25°C A 0.7 HCPL-4502/3, HCPL-0452/0453 0.6 -60 - TEMPERATURE - °C A Figure 4. Current transfer ratio vs. temperature. 8 PIN DIP, SO-8 2000 mA 5 HCPL-4502 1.9kΩ) L 1500 HCPL-0452/3 1000 t PLH 500 - TEMPERATURE - °C A Figure 5. Propagation delay vs. temperature. 8 PIN DIP, SO 1.0 0 25°C A 0.6 ...

  • Page 15

    ... I - QUIESCENT INPUT CURRENT - mA F Figure 8. Small-signal current transfer ratio vs. quiescent input current. HCPL-0452/0453/4502/4503 OPTION 060 800 P (mW) S 700 I (mA) For HCPL-4502/4503 S 600 I (mA) For HCPL-0452/0453 S 500 400 300 200 100 100 125 T - CASE TEMPERATURE - °C s Figure 9. Thermal derating curve, dependence of safety limiting value with case temperature per IEC/EN/DIN EN 60747-5-2. ...

  • Page 16

    1 PHL PLH Figure 10. Switching test circuit 10% 90% 90% 10 ...