ACPL-333J-000E Avago Technologies US Inc., ACPL-333J-000E Datasheet - Page 22

• Manufacturer Part Number: ACPL-333J-000E
• Description: OPTOCOUPLER IGBT 2.5A 16-SOIC
• Manufacturer: Avago Technologies US Inc.

Specifications of ACPL-333J-000E

• Output Type: Gate Driver, Miller Clamp
• Package / Case: 16-SOIC (0.300", 7.50mm Width)
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 2, Bi-Directional
• Current - Output / Channel: 1.5A
• Propagation Delay High - Low @ If: 180ns @ 10mA
• Current - Dc Forward (if): 12mA
• Input Type: DC
• Mounting Type: Surface Mount
• Fall Time: 50 ns
• Rise Time: 50 ns
• Configuration: 2 Channel
• Maximum Forward Diode Voltage: 1.95 V
• Minimum Forward Diode Voltage: 1.2 V
• Maximum Reverse Diode Voltage: 5 V
• Maximum Power Dissipation: 600 mW
• Maximum Operating Temperature: + 105 C
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Capacitor on FAULT Pin for High CMR
Rapid common mode transients can affect the fault pin
voltage while the fault output is in the high state. A 330
pF capacitor should be connected between the fault pin
and ground to achieve adequate CMOS noise margins at
the specified CMR value of 15 kV/μs. The added capaci-
tance does not increase the fault output delay when a
desaturation condition is detected.
Other Possible Application Circuit (Output Stage)
Figure 40. IGBT drive with negative gate drive, external booster and desaturation detection (V
VCLAMP is used as secondary gate discharge path. * indicates component required for negative gate drive topology
Figure 41. Large IGBT drive with negative gate drive, external booster. V
22
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
V
V
FAULT
V
CATHODE
ANODE
ANODE
CATHODE
V
V
FAULT
V
CATHODE
ANODE
ANODE
CATHODE
S
CC1
S
S
CC1
S
DESAT
DESAT
V
V
CLAMP
CLAMP
V
V
V
V
V
V
V
V
V
V
OUT
OUT
LED
CC2
LED
CC2
V
V
EE
EE
EE
EE
E
E
16
15
14
13
12
11
10
16
15
14
13
12
11
10
9
9
9
Optional R
Optional R
Optional R
Optional R
0.1μF 0.1μF
0.1μF 0.1μF
0.1μF
0.1μF
1
1
1
1
Optional R
Optional R
Optional R
Optional R
CLAMP
2
2
2
2
control secondary discharge path for higher power application.
Pull-up Resistor on FAULT Pin
The FAULT pin is an open collector output and therefore
requires a pull-up resistor to provide a high-level signal.
Also the FAULT output can be wire ‘OR’ed together with
other types of protection (e.g. over-temperature, over-
voltage, over-current ) to alert the microcontroller.
R
R
R
R
3
3
PULL-DOWN
PULL-DOWN
R
R
R
R
G
G
G
G
CLAMP
+ _
+ _
should be connected to V
*
*
Q1
Q2
Q1
Q2
EE
when it is not used)
V
V
V
V
+
+
+
+
-
-
-
-
CE
CE
CE
CE
3-PHASE
3-PHASE
+
+
-
-
HVDC
HVDC
HVDC
HVDC
AC
AC