LQ150X1LGB1 Sharp Microelectronics, LQ150X1LGB1 Datasheet
LQ150X1LGB1
Specifications of LQ150X1LGB1
Related parts for LQ150X1LGB1
LQ150X1LGB1 Summary of contents
Page 1
... P S RODUCT PECIFICATIONS LQ150X1LGB1 TFT-LCD Module Spec. Issue Date: November 16, 2004 AVC Liquid Crystal Displays Group No: LD-16Y04 ...
Page 2
...
Page 3
... RECORDS OF REVISION LQ150X1LGB1 SPEC No. DATE REVISED LD-16Y04 NOV. 16. 2004 SUMMARY No. PAGE NOTE 1st Issue ...
Page 4
... Application This specification applies to the color 15.0 XGA TFT-LCD module LQ150X1LGB1. These specification sheets are the proprietary product of SHARP CORPORATION(”SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP ...
Page 5
Mechanical Specifications Parameter Display size Active area Pixel format Pixel pitch Pixel configuration Display mode Unit outline dimensions *1 Mass Surface treatment *1.Note: excluding back light cables. The thickness of module (D) doesn’t contain the projection. Outline dimensions are ...
Page 6
Input Terminals 4-1. TFT-LCD panel driving CN1 (Interface signals and +3.3V DC power supply) Using connectors Corresponding connectors Using LVDS Receiver Corresponding LVDS Transmitter Pin No. Symbol 1 Vcc +3.3V Power supply 2 Vcc +3.3V Power supply 3 GND ...
Page 7
Data Mapping 1) 8 bit input Note1 pin assignment with LVDS_SET pin (Thine:THC63LVDM83R) Transmitter Pin No Data =L (GND) or Open 51 TA0 52 TA1 54 TA2 55 TA3 56 TA4 3 TA5 4 TA6 6 TB0 7 TB1 ...
Page 8
Open> RxCKIN+ RxCKIN- RXIN0+ RXIN0- RXIN1+ RXIN1- RXIN2+ RXIN2- RXIN3+ RXIN3 Display Enable NA : Not Available <LVDS_SET =H> RXCXIN+ RXCXIN- RXIN0+ RXIN0- RXIN1+ RXIN1- RXIN2+ RXIN2- RXIN3+ RXIN3 Display Enable NA : Not ...
Page 9
Note1 pin assignment with LVDS_SET pin (Thine:THC63LVDM83R) Transmitter Pin No Data =L (GND) or Open 51 TA0 52 TA1 54 TA2 55 TA3 56 TA4 3 TA5 4 TA6 6 TB0 7 TB1 11 TB2 12 ...
Page 10
Side) ①8Bit Mode LVDS_SET=L (20 pin=GND or OPEN) Controller R0-R5, G1-G5,B0, B2-B5, NA,NA, R6,R7,G6,G7, B6,B7,NA CＬ ...
Page 11
Backlight The module-side connector The user-side connector Pin no. symbol 1 Power supply for lamp 1 HIGH 2 Power supply for lamp 1 LOW 5. Absolute Maximum Ratings 5-1 module Parameter Symbol Supply voltage ...
Page 12
Electrical Characteristics 6-1. TFT-LCD panel driving Parameter 3.3V Supply voltage Current dissipation Permissive input ripple voltage Differential input High threshold voltage Low Input current (High) Input current (Low) Terminal resistor Note1 On-off sequences of Vcc and data 2.8Vcc 0.3Vcc ...
Page 13
Backlight The back light system is an edge-lighting type with four CCFTs (Cold Cathode Fluorescent Tube). The characteristics of the lamp are shown in the following table. The value mentioned below is at the case of one CCFT. CCFT ...
Page 14
Note The performance of the backlight, for example lifetime or brightness, is much influenced by the characteristics of the DC-AC inverter for the lamp. When you design or order the inverter, please make sure that a poor lighting caused by ...
Page 15
Input Data Signals and Display Position on the screen Graphics and texts can be displayed on a 1024 24 bit data signal (8bit/color [253 gray scales Display Position of input data ( ...
Page 16
Input Signals, Basic Display Colors and Gray Scale of Each Color 8-1. 8bit input Colors & Gray Gray scale Scale Black Blue Green ...
Page 17
Colors & Gray Gray scale Scale Black Blue Green Cyan Red Magenta Yellow ...
Page 18
Optical Characteristics Parameter Viewing Vertical angle range Horizontal Vertical Horizontal Contrast ratio Response time Chromaticity of White Chromaticity of Red Chromaticity of Green Chromaticity of Blue Luminance of white White Uniformity The measurement shall be executed 30 minutes after ...
Page 19
Note1 Definitions of viewing angle range: Note2 Definition of contrast ratio: The contrast ratio is defined as the following. Contrast Ratio (CR) Note3 Definition of response time: The response time is defined as the following figure and shall be measured ...
Page 20
Note5 Definition of white uniformity: White uniformity is defined as the following with five measurements 256 512 Maximum Luminance of five points (brightness) Minimum Luminance of five points (brightness) 10. Handling Precautions a) Be sure to turn ...
Page 21
Packing form a) Piling number of cartons : maximum 5 cartons b) Packing quantity in one carton : 5 module c) Carton size : 319mm(W) d) Total mass of one carton filled with full modules : 8.0kg.Max e) Packing ...
Page 22
... This specification document’s Japanese language version is also available. Its Number (SPEC.No.) is LD-16Y03. 10) When any question or issue occurs, it shall be solved by mutual discussion. Model No. Bar Code(Lot No.) Lot No. A production month (1 9,X,Y,Z) Model No. (LQ150X1LGB1) Lot No. (Date) Quantity How to express Lot No. Serial No. Administrative No. ...
Page 23
Carton storage condition Temperature Humidity 95%RH or less Reference condition : the total storage time (40 ,95%RH) : 240H or less Sunlight Be sure to shelter a product from the direct sunlight. Atmosphere ...
Page 24
...
Page 25
...
Page 26
This publication is the proprietary of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical for any ...
Page 27
... ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED event will SHARP be liable any way responsible, for any incidental or consequential economic or property damage. NORTH AMERICA SHARP Microelectronics of the Americas 5700 NW Pacific Rim Blvd. Camas, WA 98607, U.S.A. Phone: (1) 360-834-2500 ...