HCMS-3906 Avago Technologies US Inc., HCMS-3906 Datasheet - Page 16

• Manufacturer Part Number: HCMS-3906
• Description: LED DISPLAY 5X7 4CHAR 3.8MM RED
• Manufacturer: Avago Technologies US Inc.
• Series: HCMS-39xxr

Specifications of HCMS-3906

• Millicandela Rating: *
• Internal Connection: *
• Size / Dimension: *
• Color: Red
• Configuration: *
• Voltage - Forward (vf) Typ: *
• Package / Case: 12-DIP
• Display Type: Alphanumeric
• Number Of Digits/alpha: 4
• Digit/alpha Size: 0.15" (3.8mm)
• Character Format: Dot Matrix
• Character Size: 3.81mm
• Led Color: Red
• Luminous Intensity: 2.3mcd
• No. Of Digits / Alpha: 4
• Display Area Width: 17.78mm
• Display Area Height: 10.16mm
• Number Of Digits: 4
• Illumination Color: Red
• Wavelength: 635 nm
• Operating Voltage: 3.1 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Common Pin: -
• Lead Free Status / Rohs Status: Details

16
Serial/Simultaneous Data
Output D
Bit D
to switch the mode of D
between serial and simultaneous
data entry during Control
Register writes. The default mode
(logic low) is the serial D
mode. In serial mode, D
connected to the last bit (D
the Control Shift Register.
Storing logic high to bit D
changes D
mode, which affects the Control
Register only. In simultaneous
mode, D
connected to D
ment allows multiple ICs to have
their Control Registers written to
simultaneously. For example, for
n ICs in the serial mode, n * 8
clock pulses are needed to load
the same data in all Control
Registers. In the simultaneous
mode, n ICs only need 8 clock
pulses to load the same data in all
Control Registers. The propaga-
tion delay from the first IC to the
last is n * t
External Oscillator Prescaler
Bit D
Bit D
to scale the frequency of an
external Display Oscillator. When
0
1
1
of control word 1 is used
of Control Word 1 is used
OUT
0
OUT
DOUTP
is logically
to simultaneous
IN
.
. This arrange-
OUT
OUT
OUT
0
7
is
) of
this bit is logic low, the external
Display Oscillator directly sets
the internal display clock rate.
When this bit is logic high, the
external oscillator is divided by 8.
This scaled frequency then sets
the internal display clock rate. It
takes 512 cycles of the display
clock (or 8 x 512 = 4096 cycles
of an external clock with the
divide by 8 prescaler) to
completely refresh the display
once. Using the prescaler bit
allows the designer to use a
higher external oscillator
frequency without extra circuitry.
This bit has no affect on the
internal Display Oscillator
Frequency.
Bits D
These bits must always be
programmed to logic low.
Cascaded ICs
Figure 8 shows how two ICs are
connected within an HCMS-39XX
display. The first IC controls the
four left-most characters and the
second IC controls the four right-
most characters. The Dot
Registers are connected in series
to form a 320-bit dot shift
register. The location of pixel 0
has not changed. However, Dot
Shift Register bit 0 of IC2
2
-D
6
becomes bit 160 of the 320-bit
dot shift register.
The Control Registers of the two
ICs are independent of each
other. This means that to adjust
the display brightness the same
control word must be entered
into both ICs, unless the Control
Registers are set to simultaneous
mode.
Longer character string systems
can be built by cascading
multiple displays together. This is
accomplished by creating a five-
line bus. This bus consists of CE,
RS, BL, Reset, and CLK. The
display pins are connected to the
corresponding bus line. Thus, all
CE pins are connected to the CE
bus line. Similarly, bus lines for
RS, BL, Reset, and CLK are
created. Then D
the right-most display. D
this display is connected to the
next display. The left-most
display receives its D
D
D
not used.
Each display may be set to use its
internal oscillator, or the displays
may be synchronized by setting
up one display as the master and
the others as slaves. The slaves
are set to receive their oscillator
input from the master’s oscillator
output.
OUT
OUT
of the display to its right.
from the left-most display is
IN
is connected to
IN
from the
OUT
from