TORX147PL(25M,F,T) Toshiba, TORX147PL(25M,F,T) Datasheet - Page 4

• Manufacturer Part Number: TORX147PL(25M,F,T)
• Description: RECEIVER MOD TOSLINK DGTL AUDIO
• Manufacturer: Toshiba

Specifications of TORX147PL(25M,F,T)

• Data Rate: 15Mbps
• Voltage - Supply: 2.7 V ~ 3.6 V
• Power - Minimum Receivable: -24dBm
• Current - Supply: 10mA
• Applications: Digital Audio
• Product: Receiver
• Pulse Width Distortion: 15 ns
• Maximum Output Current: 2 mA
• Operating Supply Voltage: - 0.5 V to + 4.5 V
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: - 20 C
• Package / Case: Mini with Shutter
• Function: Fiber optic receiving module for digital audio interface
• Operating Voltage: 3 V
• Transmission Distance: 5 m
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: Digital Audio Optical Interface
• Other names: TORX147PL(25MFT)

(6)
(7)
(8)
(9)
(10) Soldering condition
(11) Case(receptacle) material
(12) Precautions when disposing of devices and packing materials.
(13) Precautions during use
Attaching the fiber optic receiving module
Solder the fixed pins (pins 4 and 5) of the fiber optic receiving module TORX147PL(F,T) to the printed
circuit board in order to fix it to the board.
Solvent
Supply voltage
Use the supply voltage within the recommended operating condition (V
that supply voltage does not exceed the maximum rating value of 4.5 V, even for an instant.
Output
If the receiver output is at low and is connected to the power supply, or if the output is high and is
connected to GND, the internal IC may be destroyed.
Solder at 260°C or less for no more than ten seconds.
When disposing devices and packing materials, follow the procedures stipulated by local regulations
in order to protect the environment against contamination.
Toshiba is continually working to improve the quality and the reliability of their products.
Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical
sensitivity and their vulnerability to physical stress. It is the responsibility of the buyer, when
utilizing Toshiba products, to observe standards of safety, and to avoid situations in which the
malfunction or failure of a Toshiba product could cause loss of human life, bodily injury or damage to
property.
When developing equipment, please ensure that Toshiba products are used within the specified
operating ranges set forth in the most recent product specifications. Also, please keep in mind the
precautions and conditions set forth in the Toshiba Semiconductor Reliability Handbook.
When using solvent for flux removal, do not use a high acid or high alkali solvent. Be careful not to
pour solvent in to the optical connector ports. If solvent is inadvertently poured in to them, clean it off
using cotton tips.
The case is made of polycarbonate. Polycarbonate is usually stable with acid, alcohol, and
aliphatic hydrocarbons however, with petrochemicals (such as benzene, toluene, and acetone),
alkali, aromatic hydrocarbons, or chloric hydrocarbons, polycarbonate becomes cracked, swollen,
or melted. Please take care when choosing a packaging material by referencing the table below.
〈Chemicals to avoid with polycarbonate〉
A
B
C
D
Little deterioration
But staining
Cracked crazed,
Melted
｛ ｝ ：used as solvent
Decomposed
or Swollen
PHENOMENON
・nitric acid(low concentration) , hydrogen peroxide, chlorine
・acetic acid(70% or more)
・gasoline
・methyl isobutyl ketone, ethyl acetate, butyl acetate
・methyl methacrylate, ethyl ether, MEK
・acetone, m-amino alcohol, carbon tetrachloride
・carbon disulfide, trichloroethylene, cresol
・thinners, oil of turpentine
・triethanolamine
・concentrated sulfuric acid
・benzene
・styrene, acrylonitrile, vinyl acetate
・ethylenediamine, diethylenediamine
・{chloroform, methyl chloride, tetrachloromethane, dioxane}
・ammonia water
・other alkali
{1,2-dichloroethane}
4
CHEMICALS
CC
= 2.7 to 3.6 V). Make sure
TORX147PL(F,T)
2006-12-28