HTD1 TDK Corporation, HTD1 Datasheet

HTD1

Manufacturer Part Number

HTD1

Description

PWR SUP TRIPLE 5V +12V -12V

Manufacturer

TDK Corporation

Series

Type

Commercialr

Datasheets

1.HDA-12-15.pdf (6 pages)

2.HDA-12-15.pdf (2 pages)

3.HSD24-4.8.pdf (3 pages)

Specifications of HTD1

Voltage - Output

5V, ±12V

Number Of Outputs

Power (watts)

70W

Applications

Commercial

Power Supply Type

Switching (Open Frame)

Voltage - Input

100, 120, 220, 230, 240VAC

Mounting Type

Chassis Mount

1st Output

5 VDC @ 6A

2nd Output

12 VDC @ 1.7A

3rd Output

-12 VDC @ 1.7A

Size / Dimension

11.02" L x 4.88" W x 2.76" H (280mm x 124mm x 70mm)

Power (watts) - Rated

70W

Operating Temperature

0°C ~ 70°C

Approvals

CE, EN, UL

Line Regulation

±0.05%

Load Regulation

±0.05%

Brand/series

H Series

Configuration

Open-Frame

Dimensions

4.881 in. L x 11.023 in. W x 2.755 in. H

Frequency, Input

47 to 63 Hz

Operation

Linear

Output

-12/15 VDC @ 1.7/1.5 A, 5 VDC @ 6 A, +12/15 VDC @ 1.7/1.5 A

Output Type

Triple

Power, Output

70.0 W

Primary Type

AC-DC

Special Features

Remote Sense

Standards

UL Listed, CSA Certified, CE Marked

Temperature, Operating

0 °C

Voltage, Input

100, 120, 220, 230, 240 VAC

Voltage, Output

-12/15, 5, +12/15 VDC

Voltage, Output 1

5 V

Voltage, Output 2

+12⁄15 V

Voltage, Output 3

-12⁄15 V

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

4th Output

Lead Free Status / Rohs Status

RoHS Compliant part

Current page: 1 of 6
Download datasheet (27Kb)

** Important Note

Before connecting AC power to the H Series, please verify that the power transformer is

correctly terminated as detailed section 6. Failure to do so could damage the power

supply.

Installation

1) Power Supply Terminals

2) Service Personnel

3) Earthing

4) Cooling

5) Remote sensing

6) Input connection

To meet safety requirements, the power supply terminals must not be used as the

external terminations of any equipment. The wiring of any primary circuitry should

be routed in such a way that it does not touch any secondary (output) components.

This product must only be installed in a restricted access location, accessible to

authorized competent personnel only. Some surfaces of the power supply may be

hot, and must not be touched when the product is in operation.

For protective earthing, please ensure a secure connection of the Frame Ground

terminal to the ground terminal of the equipment as the protective earth connection.

Screws and washers used must be of a suitable material as defined by the relevant

agency specifications.

The power supply must be installed where the unit is allowed free air convection.

Forced air-cooling will enhance reliability.

Some models have remote sensing to compensate for load cable drops. The H

Series units come wired for local sense from the factory. Remove the wire jumpers

and install remote sense wiring if load regulation is critical.

Remote sense wiring to the end load should ideally be twisted together and routed

separately from load cables or other noisy wiring.

The AC power is wired directly to the primary of the main power transformer. One or

two jumpers will also needed on that transformer. Connect the AC Line & Neutral

and jumper(s) as follows:

Installation Instructions – H Series

LAMBDA

HSeries

Related parts for HTD1

HTD1 Summary of contents

Page 1

Important Note Before connecting AC power to the H Series, please verify that the power transformer is correctly terminated as detailed section 6. Failure could damage the power supply. Installation 1) Power Supply Terminals To meet ...

Page 2

AC INPUT & JUMPER INFORMATION For use at: 100VAC Jumper( Apply L & fuse An external fuse (see ratings table) should be installed. Use a 125VAC or ...

Page 3

Solder the black lead to the – lead of the supply and the white lead to the + output of the supply. Double check to be sure that the + output of the supply is connected to the + lead ...

Page 4

Under all conditions, removal of input power is necessary to reset the OVP Marking The CE Marking on the product is applied to show conformance to the requirements outlined in the European Union’s Low Voltage Directive [72/73/EEC] are ...

Page 5

... HDB-12-15 0.72/0.6 2.4 1.4 80 HDC12 2.4 1.4 2.1 1.2 80 HDC15 2.1 1.2 2.1 1.2 40 HTC1 0.4/0.32 0.4/0.32 4.2 2.8 70 HTD1 0.68/0.6 0.68/0.6 OVP12 HSeries LAMBDA Model Case Size AC Input Fusing 110V A 0.5A B 1.5A C 1.5A I 2.0A A 0.5A B 1.5A C 1. ...

Page 6

AC Input EMI Leakage Current Output Voltage Adjustment Line Regulation Load Regulation Output Ripple Transient Response Temperature Coefficient Operating Temperature Range Storage Temperature Range Operating Humidity Cooling Over Voltage Protection Over Current Protection Efficiency (Typical) Remote Sensing Warranty Agency Approvals ...

Related keywords

HTD1 datasheet
HTD1 data sheet
HTD1 pdf datasheet
HTD1 component
HTD1 part
HTD1 distributor
HTD1 RoHS
HTD1 datasheet download