HS2238ECF61H Renesas Electronics America, HS2238ECF61H Datasheet
HS2238ECF61H
Specifications of HS2238ECF61H
Related parts for HS2238ECF61H
HS2238ECF61H Summary of contents
Page 1
To our customers, Old Company Name in Catalogs and Other Documents st On April 1 , 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the ...
Page 2
All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm ...
Page 3
... H8S/2237, 2238 Series FP-100A User System Interface Cable (HS2238ECF61H) for E6000 Emulator User’s Manual Rev.2.0 2003.04 ...
Page 4
Renesas neither warrants nor grants licenses of any rights of Renesas’s or any third party’s patent, copyright, trademark, or other intellectual property rights for information contained in this document. Renesas bears no responsibility for problems that may arise with ...
Page 5
... Thank you for purchasing this user system interface cable (HS2238ECF61H) for the Renesas’s original microcomputer H8S/2238 series. The HS2238ECF61H is a user system interface cable that connects an H8S/2633 series E6000 emulator (HS2633EPI61H; hereinafter referred to as the emulator) to the IC socket for a FP-100A package for the H8S/2237, H8S/2238 series MCU on the user system ...
Page 6
Section 1 Configuration....................................................................................1 Section 2 Connection Procedures ......................................................................3 2.1 Connecting User System Interface Cable to Emulator Station ......................................... 3 2.2 Connecting User System Interface Cable to User System ................................................ 5 2.2.1 Installing IC Socket ............................................................................................. 5 2.2.2 Soldering IC Socket ...
Page 7
... YAMAICHI ELECTRONICS Co., Ltd.) for the FP-100A package IC socket on the user system. Figure 1 shows the configuration of the HS2238ECF61H user system interface cable for the FP-100A package. Figure 1 HS2238ECF61H User System Interface Cable Table 1 lists the HS2238ECF61H components. Please make sure you have all of these components when unpacking. CAUTION 1 ...
Page 8
... No. Component 1 Cable body 2 Cable head 3 IC socket 4 Socket cover 5 Screws (M2 mm) 6 Documentation 2 Quantity Remarks 1 Flat cable 1 1 For the FP-100A package 1 For installing an FP-100A packaged MCU 2 For fastening cable head (with two flat washers) 1 User’s manual for HS2238ECF61H (this manual) ...
Page 9
Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station Observe the precautions listed below. Failure will result in a FIRE HAZARD and will damage the user system and the emulator product or will ...
Page 10
Figure 2 Connecting User System Interface Cable to Emulator Station 4 ...
Page 11
Connecting User System Interface Cable to User System Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 ...
Page 12
Inserting Cable Head Check the location of pin 1 before inserting. Align pin 1 on the IC socket for an FP-100A package on the user system with pin 1 on the user system interface cable head, and insert the ...
Page 13
Fasten the user system interface cable head to the IC socket for an FP-100A package on the user system with the two screws (M2.5 tightened a little at a time, alternating between screws on opposing corners. Take special care, such ...
Page 14
Fastening Cable Body Connect the cable body to the cable head. Cable body User system Figure 4 Fastening Cable Body 8 Remove jig Cable head Removing Push the remove jig. ...
Page 15
Recommended Dimensions for User System Mount Pad Figure 5 shows the recommended dimensions for the mount pad (footprint) for the user system with an IC socket for an FP-100A package (IC149-KS-11113-0: manufactured by YAMAICHI ELECTRONICS Co., Ltd.). Note that ...
Page 16
Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 6. Figure 6 Dimensions for User System Interface Cable Head 10 ...
Page 17
Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable head to the user system, are shown in figure 7. Figure 7 Resulting Dimensions after Connecting User System Interface Cable 11 ...
Page 18
Section 3 Installing the MCU to the User System 1. Check the location of pin 1 before inserting the MCU does not operate correctly, cracks might have occurred in the solder. Check conduction with a tester and re-solder ...
Page 19
Section 4 Verifying Operation 1. When using the E6000 emulator for the H8S/2633 series, turn on the emulator according to the procedures described in the H8S Series E6000 Emulator User's Manual (HS2000EPI61HE). 2. Verify the user system interface cable connections ...
Page 20
Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the cable head into the user system IC socket. 2. The dimensions of the recommended mount ...