HS2633ECN61H Renesas Electronics America, HS2633ECN61H Datasheet

Page 1

To our customers, Old Company Name in Catalogs and Other Documents st On April 1 , 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the ...

Page 2

All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm ...

Page 3

... H8S/2633 Series TQFP-120 User System Interface Cable (HS2633ECN61H) for E6000 Emulator User’s Manual ...

Page 4

Renesas neither warrants nor grants licenses of any rights of Renesas’s or any third party’s patent, copyright, trademark, or other intellectual property rights for information contained in this document. Renesas bears no responsibility for problems that may arise with ...

Page 5

... Thank you for purchasing this user system interface cable (HS2633ECN61H) for the Renesas’s original microcomputer H8S/2633 series. The HS2633ECN61H is a user system interface cable that connects an H8S/2633 series E6000 emulator (HS2633EPI61H; hereinafter referred to as the emulator) to the IC socket for a TQFP-120 package (package code: TFP-120) for the H8S/2633 series MCU on the user system ...

Page 6

Section 1 Configuration....................................................................................1 Section 2 Connection Procedures ......................................................................4 2.1 Connecting User System Interface Cable to Emulator Station ......................................... 4 2.2 Connecting User System Interface Cable to User System ................................................ 5 2.2.1 Installing IC Socket ............................................................................................. 5 2.2.2 Soldering IC Socket ...

Page 7

... Section 1 Configuration Use an IC149-120-043-B5 socket (manufactured by YAMAICHI ELECTRONICS Co., Ltd.) for the TFP-120 package IC socket on the user system. Figure 1 shows the configuration of the HS2633ECN61H user system interface cable for the TFP-120 package. CA UTION 1 ...

Page 8

... To emulator station Screws ( mm) with flat washers Figure 1 HS2633ECN61H User System Interface Cable 2 Cable body Socket cover IC socket User system Screws ( mm) with flat washers (for fastening cable head) Cable head ...

Page 9

... Table 1 lists the HS2633ECN61H components. Please make sure you have all of these components when unpacking. Table 1 HS2633ECN61H Components No. Component 1 Cable body 2 Cable head 3 IC socket 4 Socket cover 5 Screws ( mm) 6 Screws ( mm) 7 Documentation Quantity Remarks 1 Includes flat cable 1 1 For the TFP-120 package ...

Page 10

Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make ...

Page 11

Emulator station Figure 2 Connecting User System Interface Cable to Emulator Station 2.2 Connecting User System Interface Cable to User System Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to ...

Page 12

Soldering IC Socket After fastening, solder the IC socket for a TFP-120 package to the user system. Be sure to completely solder the leads so that the solder slops gently over the leads and forms solder fillets. (Use slightly ...

Page 13

Fasten the user system interface cable head to the IC socket for a TFP-120 package on the user system with the four screws ( mm; with four flat washers) provided. Each screw should be tightened a little at ...

Page 14

Connecting Cable Body to Cable Head Connect the cable body to the cable head. Cable body User system Figure 4 Fastening Cable Body 8 Remove jig Cable head Removing Push the remove jig ...

Page 15

Recommended Dimensions for User System Mount Pad Figure 5 shows the recommended dimensions for the mount pad (footprint) for the user system with an IC socket for a TFP-120 package (IC149-120-043-B5: manufactured by YAMAICHI ELECTRONICS Co., Ltd.). Note that ...

Page 16

Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 6. Figure 6 Dimensions for User System Interface Cable Head 10 Unit: mm Tolerance: –0.5 mm ...

Page 17

Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable head to the user system, are shown in figure 7. Figure 7 Resulting Dimensions after Connecting User System Interface Cable 11 ...

Page 18

Section 3 Installing the MCU to the User System 1. Check the location of pin 1 before inserting. 2. Use a Phillips-type screwdriver whose head matches the screw head. 3. The tightening torque must be 0.098 N•m or less. If ...

Page 19

MCU Pin 1 IC socket (IC149-120-043-B5 manufactured by YAMAICHI ELECTRONICS Co., Ltd.) User system Figure 8 Installing MCU to User System Screws ( mm) with flat washers Socket cover 13 ...

Page 20

Section 4 Verifying Operation 1. When using the E6000 emulator for the H8S/2633 series, turn on the emulator according to the procedures described in the H8S Series E6000 Emulator User's Manual. 2. Verify the user system interface cable connections by ...

Page 21

Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the cable head into the user system IC socket. 2. The dimensions of the recommended mount ...

Page 22

The P1 short connector is used for testing. Do not remove the short pin that is inserted in the sides of pin 1 and pin 2. Figure 11 P1 Short Connector ...