HS2636ECH61H Renesas Electronics America, HS2636ECH61H Datasheet
HS2636ECH61H
Specifications of HS2636ECH61H
Related parts for HS2636ECH61H
HS2636ECH61H Summary of contents
Page 1
To our customers, Old Company Name in Catalogs and Other Documents st On April 1 , 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the ...
Page 2
All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm ...
Page 3
... H8S/2636 Series FP-128 User System Interface Cable (HS2636ECH61H) for E6000 Emulator User’s Manual ...
Page 4
Renesas neither warrants nor grants licenses of any rights of Renesas’s or any third party’s patent, copyright, trademark, or other intellectual property rights for information contained in this document. Renesas bears no responsibility for problems that may arise with ...
Page 5
... Thank you for purchasing this user system interface cable (HS2636ECH61H) for the Renesas’s original microcomputer H8S/2636 series. The HS2636ECH61H is a user system interface cable that connects an H8S/2636 and H8S/2646 series E6000 emulator (HS2646EPI61H; hereinafter referred to as the emulator) to the IC socket for a FP-128 package for the H8S/2636 series MCU on the user system ...
Page 6
Section 1 Configuration....................................................................................1 Section 2 Connection Procedures ......................................................................4 2.1 Connecting User System Interface Cable to Emulator Station ......................................... 4 2.2 Connecting User System Interface Cable to User System ................................................ 6 2.2.1 Installing IC Socket ............................................................................................. 6 2.2.2 Soldering IC Socket ...
Page 7
... Section 1 Configuration Use an NQPACK128RD socket (manufactured by Tokyo Eletech Corporation) for the FP-128 package IC socket on the user system. Figure 1 shows the configuration of the HS2636ECH61H user system interface cable for the FP-128 package. CAUTION 1 ...
Page 8
... Figure 1 HS2636ECH61H User System Interface Cable 2 ...
Page 9
... Table 1 lists the HS2636ECH61H components. Please make sure you have all of these components when unpacking. Table 1 HS2636ECH61H Components No. Component 1 Cable body 2 Cable head 3 IC socket 4 Socket cover 5 Screws ( mm) 6 Screws ( mm) 7 Guide pins 8 Screwdriver 9 Documentation Quantity Remarks 1 Flat cable 1 1 For the FP-128 package ...
Page 10
Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station Observe the precautions listed below. Failure will result in a FIRE HAZARD and will damage the user system and the emulator product or will ...
Page 11
Figure 2 Connecting User System Interface Cable to Emulator Station 5 ...
Page 12
Connecting User System Interface Cable to User System Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 ...
Page 13
Bottom view of IC soket Figure 3 Location Setting of IC Socket 2.2.2 Soldering IC Socket After fastening, solder the IC socket for an FP-128 package to the user system. Be sure ...
Page 14
Fastening Cable Head 1. Use the screwdriber provided for tightening screws. 2. The tightening torque must be 0.054 N•m or less. If the applied torque cannot be accurately measured, stop tightening when the force required to turn the screw ...
Page 15
Figure 4 Connecting User System Interface Cable to User System 9 ...
Page 16
Fastening Cable Body Connect the cable body to the cable head. Cable body User system Figure 5 Fastening Cable Body 10 Remove jig Cable head Removing Push the remove jig ...
Page 17
Recommended Dimensions for User System Mount Pad Figure 6 shows the recommended dimensions for the mount pad (footprint) for the user system with an IC socket for an FP-128 package (NQPACK128RD: manufactured by Tokyo Eletech Corporation). Note that the ...
Page 18
Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 7. Figure 7 Dimensions for User System Interface Cable Head 12 ...
Page 19
Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable head to the user system, are shown in figure 8. Figure 8 Resulting Dimensions after Connecting User System Interface Cable 13 ...
Page 20
Section 3 Installing the MCU to the User System 1. Check the location of pin 1 before inserting. 2. Use the screwdriver provided for tightening screws. 3. The tightening torque must be 0.054 N•m or less. If the applied torque ...
Page 21
Figure 9 Installing MCU to User System 15 ...
Page 22
Section 4 Verifying Operation 1. When using the E6000 emulator for the H8S/2636 series, turn on the emulator according to the procedures described in the H8S Series E6000 Emulator User's Manual (HS2000EPI61HE). 2. Verify the user system interface cable connections ...
Page 23
Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the cable head into the user system IC socket. 2. The dimensions of the recommended mount ...
Page 24
The P1 jumper socket is used for testing. Do not remove the inserted jumper pin. 18 Figure 12 P1 Jumper Socket ...