STEVAL-ISA025V1 STMicroelectronics, STEVAL-ISA025V1 Datasheet - Page 28

• Manufacturer Part Number: STEVAL-ISA025V1
• Description: EVAL BOARD 30A 400KHZ L6730
• Manufacturer: STMicroelectronics
• Type: DC/DC Switching Converters, Regulators & Controllersr

Specifications of STEVAL-ISA025V1

• Design Resources: STEVAL-ISA025V1 Gerber Files STEVAL-ISA025V1 Schematic STEVAL-ISA025V1 Bill of Materials
• Main Purpose: DC/DC, Step Down
• Outputs And Type: 1, Non-Isolated
• Voltage - Output: 3.3V
• Current - Output: 30A
• Voltage - Input: 4.5 ~ 14V
• Regulator Topology: Buck
• Frequency - Switching: 400kHz
• Board Type: Fully Populated
• Utilized Ic / Part: L6730
• Input Voltage: 4.5 V to 14 V
• Output Voltage: 3.3 V
• Product: Power Management Modules
• Silicon Manufacturer: ST Micro
• Silicon Core Number: L6730
• Kit Application Type: Power Management - Voltage Regulator
• Rohs Compliant: No
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Power - Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• For Use With/related Products: L6730
• Other names: 497-5868

Device description
5.11
28/52
Table 7
Figure 23. External resistor
Table 7.
Synchronization
The presence of many converters on the same board can generate beating frequency noise.
To avoid this it is important to make them operate at the same switching frequency.
Moreover, a phase shift between different modules helps to minimize the RMS current on
the common input capacitors.
synchronization. Two or more devices can be synchronized simply connecting together the
SYNCH pins. The device with the higher switching frequency will be the Master while the
other one will be the slave. The slave controller will increase its switching frequency
reducing the ramp amplitude proportionally and then the modulator gain will be increased.
To avoid a huge variation of the modulator gain, the best way to synchronize two or more
devices is to make them work at the same switching frequency and, in any case, the
switching frequencies can differ for a maximum of 50% of the lowest one. If, during
synchronization between two (or more) L6730, it’s important to know in advance which the
master is, it’s timely to set its switching frequency at least 15% higher than the slave. Using
an external clock signal (f
different switching frequency (f
6.2KΩ
4.3KΩ
2.7KΩ
1.8KΩ
1.2KΩ
11KΩ
N.C
0Ω
R1
shows how to set the different options through an external resistor divider:
S/O/U and CC/O/U pin
2.7KΩ
2.7KΩ
2.7KΩ
2.7KΩ
2.7KΩ
2.7KΩ
N.C
R2
0Ω
EXT
) to synchronize one or more devices that are working at a
Figure 24
R2
Doc ID 11938 Rev 3
SW
R1
V
) it is recommended to follow the below formula:
SOU
f
SW
0.2
0.3
0.4
0.5
0.6
0.7
/V
0
1
≤
CCDR
shows the results of two modules in
f
EXT
≤
CC/O/U
VCCDR
S/O/U
1
12V BUS
12V BUS
12V BUS
12V BUS
5V BUS
5V BUS
5V BUS
5V BUS
3 ,
UVLO
⋅
L6730/B
f
SW
Not latched
Not latched
Not latched
Not latched
Latched
Latched
Latched
Latched
OVP
L6730 - L6730B
SINK CC
Not
Yes
Not
Yes
Not
Yes
Not
Yes